![background image](http://html.mh-extra.com/html/marantz/pmd650/pmd650_service-manual_1725431009.webp)
7
10. Press the
STOP
button and display "LDPWR CHK". and
stop the laser emission.
The
STOP
button is effective at all times to stop the laser
emission.
3-7. TRAVERSE (E-F BALANCE) ADJUSTMENT
Note 1 :
Data will be erased during MO reading if a recorded
disc is used in this adjustment.
Note 2 :
If the traverse waveform is not clear. connect the
oscilloscope as shown in the following figure so that
it can be seen more clearly.
Connection:
Osilloscope
(DC range)
JQ20 pin 3 (TEO)
330k
10p
+
-
JQ20 pin 2 (VC)
V : 0.1 V/div
H : 10 ms/div
( )
Adjusting Method:
1. Connect an oscilloscope to JQ20 pin 3 (TEO) and JQ20
pin 2 (VC) of the MD board (PQ01).
2. Load a low reflection disc (any available on the market).
(Refer to Note 1.)
3. Press the
button or
button and move the optical
pick-up outside the pit.
4. Use the
EDIT(<, >)
buttons and display "EFBAL ADJ".
5. Press the
ENTER
button and display "EFBAL MO".
(Laser power READ power/Focus servo ON/tracking servo
OFF/spindle (S) servo ON)
6. Press the
ENTER
button.
7. Use the
EDIT(<, >)
buttons so that the waveforms of the
oscilloscope becomes the specified value. (When the the
EDIT(<, >)
buttons is Used, the "
" of "MOr EFB=
"
changes and the waveform changes.) In this adjustment,
waveform varies at intervals of approx. 2%. Adjust the wave-
form so that the specified value is satisfied as much as
possible. (MO read power traverse adjustment)
(Traverse Waveform)
specification : A = B
8. Press the
ENTER
button, and save the result of adjust-
ment to the non-volatile memory. ("DATA SAVE" will be
displayed for a moment. Then "MOw EFB= " will be dis-
played.) The optical pick-up moves to the pit area auto-
matically and servo is imposed.
9. Use the
EDIT(<, >)
buttons so that the waveforms of the
oscilloscope becomes the specified value. (When the the
EDIT(<, >)
buttons is Used, the "
" of "MOw EFB=
"
changes and the waveform changes.) In this adjustment,
waveform varies at intervals of approx. 2%. Adjust the
waveform so that the specified value is satisfied as much
as possible.
接続
接続
接続
接続
接続 :
:
:
:
:
Osilloscope
(DC range)
JQ20 pin 3 (TEO)
330k
10p
+
-
JQ20 pin 2 (VC)
V : 0.1 V/div
H : 10 ms/div
( )
調整方法
調整方法
調整方法
調整方法
調整方法 :
:
:
:
:
1. オシロスコープを MD 基板(PQ01)の JQ20 3 ピン(TEO)と JQ20
2 ピン(VC)に接続する。
2.市販の低反射ディスク(ブランクディスク)を挿入する。(注意
. 参照)
3.
ボタン、
ボタンを押して光ピックアップをピット部よ
り外周に移動する。
4.EDIT(<, >)
EDIT(<, >)
EDIT(<, >)
EDIT(<, >)
EDIT(<, >)ボタンを押して表示を
"
EFBAL ADJ
"
にする。
5.ENTER
ENTER
ENTER
ENTER
ENTER ボタンを押して表示を
"
EFBAL MO
"
にする。
(これはレーザーパワー : READ パワー , フォーカスサーボ
: ON, トラッキングサーボ : OFF, スピンドル(S)サーボ :
ON の状態)
6. 再度、ENTER
ENTER
ENTER
ENTER
ENTER ボタンを押します。
7. オシロスコープの波形が規格値になるように EDIT(<, >)
EDIT(<, >)
EDIT(<, >)
EDIT(<, >)
EDIT(<, >)ボ
タンを押して調整する。
(EDIT(<, >)
EDIT(<, >)
EDIT(<, >)
EDIT(<, >)
EDIT(<, >)ボタンを押すと、
"
MOr EFB=
"
の
"
"
数字が変
化し、波形も変化します。)
この調整は約 2% 刻みで変化し、最も規格値に近づくように
調整する。
(MO リードパワートラバース調整)
(トラバース波形 規格:A = B)
8. ENTER
ENTER
ENTER
ENTER
ENTERボタンを押して不揮発性メモリに調整結果をセーブす
る。(この時、一瞬
"
DATA SAVE
"
と表示される。)
その後に
"
MOw EFB=
"
と表示される。自動的にピット部の内
周まで光ピックアップが移動してサーボがかかる。
9. この時のオシロスコープの波形が規格値に近づくようにEDIT
EDIT
EDIT
EDIT
EDIT
(<, >)
(<, >)
(<, >)
(<, >)
(<, >)ボタンを押して調整する。
(EDIT(<, >)
EDIT(<, >)
EDIT(<, >)
EDIT(<, >)
EDIT(<, >)ボタンを押すと、
"
MOw EFB=
"
の
"
"
数字が変
化し、波形も変化します。)
この調整は約2%刻みで変化し、最も規格値に近づくように調
整する。
(MO ライトパワートラバース調整)
(トラバース波形 規格:A = B)
10.ENTER
ENTER
ENTER
ENTER
ENTER ボタンを押して不揮発性メモリに調整結果をセーブす
る。(この時、一瞬
"
DATA SAVE
"
と表示される。)
その後
"
MOp EFB=
"
と表示される。