![background image](http://html.mh-extra.com/html/marantz/pmd650/pmd650_service-manual_1725431011.webp)
9
18. Press the
ENTER
button, and save the result of adjust-
ment to the non-volatile memory. ("DATA SAVE" will be dis-
played for a moment. Then "EFBAL ADJ" will be displayed.)
19. Press the
EJECT
switch and remove the test disc. ( High
reflection disc TMD-381 )
3-8. FOCUS BIAS ADJUSTMENT
Connection:
Jitter Meter
+
-
JQ20 1pin(RF)
JQ20 2pin(VC)
Adjusting Method:
1. Load a continuously recorded disc (Refer to "3-4. Creating
MO Continuously Recorded. Disc".).
2. Use the
EDIT(<, >)
buttons and display "FBIAS ADJ".
3. Press the
ENTER
button and display "a =
".
4. Press the ">" of the
EDIT(<, >)
button and find the focus
bias value at which the reading of the jitter meter becomes
27 ns to 30 ns. (Refer to note 2.) If the reading of the jitter
meter is over 30 ns, press the "<" of the
EDIT(<, >)
button.
It will be down.
5. Press the
ENTER
button and display "b =
".
6. Press the "<" of the
EDIT(<, >)
button and find the focus
bias value at which the reading of the jitter meter becomes
27 ns to 30 ns. (Refer to note 2.) If the reading of the jitter
meter is over 30 ns, press the "
>
" of the
EDIT(<, >)
button.
It will be down.
Note :
If the sarvo is out and It stops to adjust, press the
STOP
button. The display will show "ADJ CANCEL", and the
display return to "FBIAS ADJ".
7. Press the
ENTER
button, and save the result of adjustment
to the non-volatile memory. ("DATA SAVE" will be displayed
for a moment. ) Then "c =
" will be displayed.
8. Press the
DISPLAY
button and display "C1
AD
" and
check that the C1 error rate is below 50 and ADER is 00.
Then press the
STOP
button. The first four digits indicate
the C1 error rate, the two digits after indicate ADER.
9. If the reading of the jitter meter is over 28 ns, press the
STOP
button ("FBIAS ADJ" will be displayed.) and adjust it
again.
10. Press the
STOP
button and slide the
EJECT
switch to
remove the continuously recorded disc.
Note 1 :
The relation between the C1 error and jiter meter is as
shown in the following figure. Find points
a
and
b
in
the following figure using the above adjustment. The
focal point position
c
is automatically calculated from
points
a
and
b
.
Note 2 :
As the jiter meter changes, perform the adjustment
using the average vale.
4.EDIT(>)
EDIT(>)
EDIT(>)
EDIT(>)
EDIT(>)ボタン(必ず、>)を押してジッターメータ値が 27 nS
〜30 nSになるフォーカスバイアス量を見つける。(注意2.参
照)30 nSを超えたときのみ(<)
(<)
(<)
(<)
(<)ボタンで少し下げる。(a点側の
ジッターの最大値を設定)
5.ENTER
ENTER
ENTER
ENTER
ENTER ボタンを押して表示を
"
b =
"
にする。
6.EDIT(<)
EDIT(<)
EDIT(<)
EDIT(<)
EDIT(<)ボタン(必ず、<)を押してジッターメータ値が 27 nS
〜30 nS になるフォーカスバイアス量を見つける。(注意 2. 参
照)30 nSを超えたときのみ(>)
(>)
(>)
(>)
(>)ボタンで少し下げる。(b点側の
ジッターの最大値を設定)
注意
注意
注意
注意
注意 :
:
:
:
: サーボが外れたとき及び調整を中止するときは、STOP
STOP
STOP
STOP
STOP
ボタンを押すと
"
ADJ CANCEL
"
を表示して(調整データは
セーブされない。)、その後表示は
"
FBIAS ADJ
"
に戻る。
(項目選択)
STOP
STOP
STOP
STOP
STOP ボタンはいつでも受け付け、調整を止めます。
7.ENTER
ENTER
ENTER
ENTER
ENTER ボタンを押して不揮発性メモリに調整結果をセーブす
る。 (この時、一瞬
"
DATA SAVE
"
と表示される。)
その後
"
c =
"
と表示される。(c 点は自動調整)
8. この時、DISPLAY
DISPLAY
DISPLAY
DISPLAY
DISPLAY ボタンを押して、
"
C1
AD
"
と表示する。
C1 エラーレート表示が 50 以下で ADER が 00 であることを確認
して STOP
STOP
STOP
STOP
STOP ボタンを押す。最初の 4 桁の数字が C1 エラーレー
ト、後の 2 桁の数字が ADER を示す。
9. ジッターメータ値が28 nS以上の時はSTOP
STOP
STOP
STOP
STOPボタンを押して再
度、調整をする。
"
FBIAS ADJ
"
に戻る。(項目選択)
10.STOP
STOP
STOP
STOP
STOPボタンを押し、次に EJECT
EJECT
EJECT
EJECT
EJECTスイッチをスライドして連続
録音済ディスクを取り出す。
注意
注意
注意
注意
注意 :
:
:
:
:
1.C1エラーとジッターメータ値の関係を示すと下図のようにな
ります。 上記調整で下図の
a
aa
aa
,
b
bb
bb
点を見つけます。合焦点位置
c
cc
cc
点は
a
aa
aa
,
b
bb
bb
点から自動的に計算し求めます。
2. ジッターメータ値は変動しますので、平均値を読み調整を行
うようにしてください。
Error
Focus bias value
(F.BIAS)
b
c
a
30ns
3‑9.
3‑9.
3‑9.
3‑9.
3‑9. エラーレート確認
エラーレート確認
エラーレート確認
エラーレート確認
エラーレート確認
3‑9‑1.
3‑9‑1.
3‑9‑1.
3‑9‑1.
3‑9‑1. 高反射ディスクエラーレート確認
高反射ディスクエラーレート確認
高反射ディスクエラーレート確認
高反射ディスクエラーレート確認
高反射ディスクエラーレート確認
確認方法
確認方法
確認方法
確認方法
確認方法 :
:
:
:
:
1. 高反射ディスク A‑BEX TMD‑381 を挿入する。
2.EDIT(<, >)
EDIT(<, >)
EDIT(<, >)
EDIT(<, >)
EDIT(<, >)ボタンを押して表示を
"
CPLAY MODE
"
にする。
3.ENTER
ENTER
ENTER
ENTER
ENTER ボタンを押すと表示が 1 秒間
"
CPLAY MID
"
となった後、
表示が
"
C1
AD
"
に変わる。
4.C1 エラーレートが 20 以下であることを確認する。
5.STOP
STOP
STOP
STOP
STOP ボタンを押して再生を止め、EJECT
EJECT
EJECT
EJECT
EJECT スイッチをスライド
して高反射ディスクを取り出す。