background image

MANN+HUMMEL IQORON 

 MANN+HUMMEL Industrial Filters 

 

 

 

 

 

 

         8 

6.1

 

Maintenance plan 

6.2

 

Maintenance  of  the  main  filter 
element 

 

Maintenance of the main filter 
element (Pos. 2) need only be 
performed when the maintenance 
indicator/switch has been triggered 
or according to the device or engine 
manufacturer's instructions. 

 

Regardless of the number of 
operating hours, the main filter 
element must be changed after 2 
years at the latest. 

Never continue to use damaged 
main filter elements.  

In case of doubt, always install a 
new main filter element. 

 

6.2.1

 

Disassembling the main filter 
element 

 

Unlock  the  wire  clamp  fasteners  (Pos.  9) 
and remove the housing cover (Pos. 1). 

 

Remove the main filter element (Pos. 2) and 
dispose of it according to local regulations. 

 

Clean  the  inside  of  the  housing,  frame  and 
lid thoroughly with a damp cloth. In the case 
of  filters  without  a  secondary  element,  pay 
particular  attention  here  that  no  dust  or  dirt 
gets into the clean air side of the filter. 

 

Check all the parts for signs of damage and 
wear, replace them as necessary. 

IQORON series 10, 12 and 14: 

 

Move  the  red  clamping  bar  towards 
"Unlock" (refer to Fig. 4). 

 

Remove  the  frame  (Pos.  11)  together  with 
the main filter element (Pos. 2). 

 

Remove  the  main  filter  element  from  the 
frame  and  dispose  of  it  according  to  the 
local regulations.  

 

6.2.2

 

Cleaning the main filter element 

 

Never wash out or beat the main 
filter element.  
When blowing clean, ensure no 
dust gets into the inside of the main 
filter element. 

 

Since small defects are difficult to 
detect or cannot be detected, we 
recommend always installing new 
elements to protect engines or 
equipment! 

We assume no liability for the 
suitability of cleaned elements. 

 

Clean 

the 

main 

filter 

element 

with 

compressed  air  (maximum  5  bar)  carefully, 
applying the compressed air from the clean 
side  (seal  side)  until  no  more  dust 
development  occurs.  The  tip  of  the 
compressed  air  gun  must  not  touch  the 
main filter element. 

 

 

Fig. 4 

Unlocking the main filter element frame  

 

Fig. 5 

Cleaning the IQORON main filter element 

(Fig. illustrates size 7) 

Summary of Contents for IQORON 10














Reviews: