Manitowoc S model Installation, Use & Care Manual Download Page 31

Page: 31 / 72

Section 2

Installation Instructions

Part Number 000002477 3/08

2-19

WATER SUPPLY AND DRAIN LINE SIZING/CONNECTIONS

Refer to “Ice Machine Dimensions” at the beginning of Section 2 for the exact locations of inlets and drains for the model you are working on.

Typical Water Supply Drain Installation

Caution

Plumbing must conform to state and local codes.

Location

Water Temperature

Water Pressure

Ice Machine Fitting

Tubing Size Up to Ice

Machine Fitting

Ice Making
Water Inlet

°F (1.6°C) Min.

°F (32.2°C) Max.

20 psi (1.4 bar) Min.

80 psi (5.5 bar) Max.

3/8” Female Pipe

Thread

3/8” (9.5 mm) min. inside

diameter

Water Cooled

Condenser

°F (1.6°C) Min.

°F (32.2°C) Max.

Standard

20 psi (1.4 bar) Min.

150 psi (10.3 bar) Max.

High Pressure Option

20 psi (1.4 bar) Min.

350 psi (24.1 bar) Max.

1/2” Female Pipe

Thread

1/2” (12.7 mm) min. inside

diameter

Ice Making

Water Drain

---

1/2” Female Pipe

Thread

1/2” (12.7 mm) min. inside

diameter

Bin Drain

---

3/4” Female Pipe

Thread

3/4” (19.1 mm) min.

inside diameter

Large Capacity

Bin Drain

---

1” Female Pipe Thread

1” (25.4 mm) min.

inside diameter

18.00” VENT

(45.70 cm)

ICE MAKING WATER

DRAIN FITTING

1/2” F.P.T. (1.27 cm)

BIN DRAIN TUBING

3/4”MIN. I.D. (1.91 cm)

AIR GAP

OPEN, TRAPPED OR

VENTED DRAIN

DO NOT TRAP

MUST HAVE

AIR-GAP

INCORRECT

Summary of Contents for S model









































































Search results

Summary of Contents for S model

Reviews:

Related manuals for S model

Brands by name

Popular brands

Manitowoc S model, Installation, Use & Care Manual

Search results

Summary of Contents for S model

Reviews:

Related manuals for S model

Brands by name

Popular brands