Manitowoc S model Installation, Use & Care Manual Download Page 28

Page: 28 / 72

Installation Instructions

Section 2

2-16

Part Number 000002477 3/08

Condensing Unit Wiring Connections

CVD CONDENSING UNIT
208-230/1/60

CVD CONDENSING UNIT
208-230/3/60

CVD CONDENSING UNIT
230/1/50

Warning

These diagrams are not intended to show proper
wire routing, wire sizing, disconnects, etc., only the
correct wire connections.

All electrical work, including wire routing and
grounding, must conform to local, state and national
electrical codes.

Though wire nuts are shown in the drawings, the ice
machine field wiring connections may use either
wire nuts or screw terminals.

GROUND

CONDENSING UNIT

CONNECTIONS

TO SEPARATE

FUSE/BREAKER

SV1258

GROUND

CVD2085 ONLY

CONDENSING UNIT CONNECTIONS

TO SEPARATE

FUSE/BREAKER

SV1258a

CONTACTOR

GROUND

CONDENSING

UNIT

CONNECTIONS

TO SEPARATE

FUSE/BREAKER

GROUND

TO SEPARATE

FUSE/BREAKER

SV1190a

CONTACTOR

CVD2085 ONLY

CONDENSING UNIT CONNECTIONS

GROUND

CONDENSING UNIT

CONNECTIONS

TO SEPARATE

FUSE/BREAKER.

DISCONNECT ALL

POLES.

Summary of Contents for S model









































































Search results

Summary of Contents for S model

Reviews:

Related manuals for S model

Brands by name

Popular brands

Manitowoc S model, Installation, Use & Care Manual

Search results

Summary of Contents for S model

Reviews:

Related manuals for S model

Brands by name

Popular brands