manualshive.com logo in svg

Manitowoc RF0300, Technician'S Handbook

Share
Download
Manitowoc RF0300 Technician'S Handbook Download Page 147

Part Number 000007661 11/16  

147

RN1000C/RN1200C Troubleshooting

NOTE: Refer to “RN1000C/RN1200C” on page 39 for 
normal sequence of operation

INDICATOR LIGHT OPERATION

The lights on the control board can be used as quick 
failure mode indicators. If the failure mode isn’t 
obvious from the light indicators, use the flowchart to 
systematically eliminate issues.
NOTE: Each relay on the control board has a light adjacent 
to the relay to indicate the relay coil has power.

Indicator light legend

ON          OFF       ON or OFF       FLASHING

1.  Normal light operation, No Ice

•  Defective compressor or start component
•  Defective contactor
•  Defective control board relay

PURGE (Y) 

PO

WER (G) 

LO

W BIN (G) 

AU

GER ON (G) 

REFRIG ON (G) 

CLEANING (Y) 

SE

RV

ICE (R) 

HI 

AMPS (R) 

HI PRESS (R) 

LO

 PRESS (R) 

DRAIN CL

OG (R) 

TIME DELA

Y (Y)

 

LO

 WA

TER (R) 

CPU (G) 

HI 

WA

TER (R) 

Summary of Contents for RF0300





























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands