manualshive.com logo in svg

Manitowoc RF0300, Technician'S Handbook

Share
Download
Manitowoc RF0300 Technician'S Handbook Download Page 116

116 

Part Number 000007661 11/16 

RF2300R/RFS2300R Troubleshooting

HEAD SECTION FOR RACK REFRIGERATION SYSTEMS
Normal Operation

When the toggle switch is placed in the ON position the 
following controls must be in the closed position before 
the ice machine will start:

A.  Bin Thermostat
B.  Ice Chute Safety Switch
C.  Low Water Level Switch

Placing the toggle switch in the ON position starts the 
gear motor. After the rotation speed sensor verifies 10 
minutes of correct rotation the time delay ends and the 
liquid line and suction solenoid valves energize. 
The ice machine will continue to make ice until ice 
contacts the bin thermostat and the liquid line and 
suction solenoid valves close.
The ice machine remains off until ice no longer contacts 
the bin thermostat.

ROTATION SENSOR OPERATION

light

Definition

Yellow Blinking

Time Delay Period

Yellow Solid

Normal Operation Sensing

Red Blinking

Fault Time Delay Period

Red Solid

Lockout - 8 Consecutive Faults

Remove/Restore Power To Reset

Summary of Contents for RF0300





























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands