manualshive.com logo in svg

Manitowoc Grove GRT880, Operator'S Manual

Share
Download
Manitowoc Grove GRT880 Operator'S Manual Download Page 194

5-28

Published 3-25-2020, Control # 643-04

MAINTENANCE AND LUBRICATION

GRT880 OPERATOR MANUAL

RUST PROTECTION

Grove cranes are manufactured to high quality standards,
including the type of paint finish demanded by today's
industry. In partnership with our paint supplier, we are also
doing our part to help prevent premature corrosion of cranes. 

Grove cranes will be treated with a rust inhibitor called
Carwell

®

 

T32-CP-90. While a rust inhibitor cannot guarantee

that a machine will never rust, this product will help protect
against corrosion on Grove cranes that are treated with this
product. 

Carwell

®

 is a treatment, not a coating. It contains no

silicones, solvents, Chlorofluorocarbons (CFC) or anything
that would be classified as hazardous under OSHA
Regulation 29 CFR 19 10.1200. The product is a liquid blend
of petroleum derivatives, rust inhibitors, water-repelling and
water-displacing agents.

Special equipment is used to spray a light film on the entire
undercarriage and various other areas of each new crane
before shipment. When applied, the product has a red tint to
allow applicators to view coverage. This red tint turns clear
within approximately 24 hours after application. 

Once applied, treatment can appear to leave a slightly “oily”
residue on painted surfaces and until the red tinting fades,
could be mistaken for a hydraulic oil leak. While the product
is not harmful to painted surfaces, glass, plastic or rubber, it
m u s t  b e   r e m o v e d  u s i ng   s ta n d ar d  s t e am - c l e a ni n g
techniques. 

This treatment works in various ways: (1) it eliminates the
moisture containing salt, dirt and other pollutants by lifting
and removing them from the metal surface; (2) the film
creates a barrier to repel further moisture from coming in
contact with the metal; and (3) it penetrates crevices. 

In addition to the factory-applied treatment, Grove crane
owners must provide proper maintenance and care to help
ensure long-term protection of their crane against corrosion.
This procedure provides information and guidelines to help
maintain the paint finish on Grove cranes. 

The most common causes of corrosion include the following: 

•

Road salts, chemicals, dirt, and moisture trapped in the
hard-to-reach areas; 

•

Chipping or wear of paint, caused by minor incidents or
moving components; 

•

Damage caused by personal abuse, such as using the
decks to transport rigging gear, tools, or cribbing; and 

•

Exposure  to  harsh  environmental  hazards  such  as
alkaline, acids, or other chemicals that can attack the
crane's paint finish. 

While crane surfaces that are easily seen have the biggest
impact on appearance, particular attention should be given
to the undercarriage to minimize harmful effects of corrosion. 

Exercise special care and increase frequency of cleaning if
crane is operated: 

•

on  roads  where  large  quantities  of  salt  or  calcium  are
applied to treat icy and snowy road surfaces; 

•

in areas that use dust control chemicals; 

•

anywhere  there  are  increased  levels  of  wetness  -
especially near salt water; 

•

during  prolonged  periods  of  exposure  to  damp
conditions (e.g., moisture held in mud), where certain
crane parts may become corroded even though other
parts remain dry; or 

•

in  high  humidity,  or  when  temperatures  are  just  above
the freezing point. 

Cleaning Procedures

To help protect against corrosion of Grove cranes,
Manitowoc Crane Care recommends washing the crane at
least monthly to remove all foreign matter. More frequent
cleaning may be needed when operating in harsh
environmental conditions. To clean the crane, follow these
guidelines: 

•

High  pressure  water  or  steam  is  effective  for  cleaning
the crane's undercarriage and wheel housings. Keeping
these areas clean will not only help retard the effects of
corrosion, but also improve the ability to identify
potential issues before they grow into larger problems.

•

Rinse  dirt  and  dust  off  before  washing  the  crane.  Dirt
can scratch the crane's finish during washing/cleaning. 

•

Hard to clean spots caused by road tar or bugs should
be treated and cleaned after rinsing and before washing.
Do not use solvents or gasoline.

•

Wash  using  only  soaps  and  detergents  recommended
for automotive paint finishes. 

•

Rinse  all  surfaces  thoroughly  to  prevent  streaking
caused by soap residue.

•

Allow crane to dry thoroughly. You can accelerate drying
by using compressed air to remove excess water. 

NOTE:

Polishing and waxing (using automotive-type wax)
is recommended to maintain original paint finish. 

CAUTION

High pressure water can be forced into spaces and
infiltrate beyond seals. Avoid pressure washing near
electrical controls, panels, wiring, sensors, hydraulic
hoses and fittings, or anything that can be damaged by
high pressure cleaning/spraying.

Summary of Contents for Grove GRT880











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands