manualshive.com logo in svg

Manitowoc 1814E, Installation, Operation And Maintenance Manual, Page: 23 / 42

Share
Download
Manitowoc 1814E Installation, Operation And Maintenance Manual Download Page 23

4-3 

A FilterQuick™ controller controls the semi-automatic filtration system on the 1814E with 
FilterQuick™ fryer.  After a preset number of cook cycles the controller displays 

Filter now?

 

alternating with 

YES NO

.  If 

NO

 is selected or a cook cycle is started, the controller will resume 

normal operation for a set amount of cooks and then prompt for a filter again.  The FILTER NOW? 
prompt is displayed once the cooks till filter or filter prompt count is satisfied.  Refer to the 
FilterQuick™ controller manual for filter steps. All messages need to be confirmed or cleared on all 
controllers prior to starting any filtration process. 
 

4.4 

Troubleshooting the 1814E with FilterQuick™ with Fingertip Filtration 

4.4.1 Incomplete 

Filtration 

 

Should the filter procedure fail after the filter paper or pad was changed an error message is 
generated.  

 

The controller displays 

IS VAT FULL?

 alternating with 

yes no. 

The MIB board displays three horizontal lines.    
 

 

 

1.  If the vat is full press the 

 

(YES) 

button to continue.  The controller 

returns to idle cook mode or OFF. 

 

 If the pot is not filled completely continue to next step. 

 

 

 

2.   Press 

 

(NO)

 

if pot is not filled completely. 

 
 

 

 

The controller displays 

FILLING

 while the pump runs again.  When the pump stops, the controller 

displays 

IS VAT FULL?

 alternating with 

yes no

 again.  If the vat is full go to step 1.  If the 

vat is not completely filled continue.  

 

3.   Press 

 

(NO)

 

if pot is not filled completely. 

 
 

 

 

The controller displays 

FILLING

 while the pump runs again.  When the pump stops, the controller 

displays 

IS VAT FULL?

 alternating with 

yes no

 again.  If the vat is full go to step 1.  If the 

vat is not completely filled continue.  

 

4.   Press 

 

(NO)

 if pot is not filled completely. If this is the sixth 

consecutive sequence of incomplete filtration skip to step 8. 

 
 

 

 

The controller displays 

CHANGE FILTER PAPER? 

alternating with 

YES NO

 and an 

alarm.   

 

5.   Press 

 

(YES) 

to continue.  

 

Pressing 

 

(NO)

 allows the fryer to return to cook mode in most cases for 

four minutes or 15 minutes if the paper is expired*, ending with the 

CHANGE FILTER PAPER? 

alternating with 

YES NO

 display.   

This repeats until 

YES

 is chosen.  

 

 

 

Summary of Contents for 1814E











































Reviews:

No comments