Manhattan MSKL MS-3020 User Manual Download Page 2

 

MSKL MS-3020 User Manual 

FCC Compliances Statement 

 

This equipment has been tested and found to comply with the limits for a Class B digital device, 

pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection 
against harmful interference in residential installations. This equipment generates, uses, and can 

radiate radio frequency energy, and if not installed and used in accordance with the instructions, may 

cause harmful interference to radio communications. However, there is not guarantee that 

interference will not occur in a particular installation. If this equipment does cause interference to 

radio or television equipment reception, which can be determined by turning the equipment off and 

on, the user is encouraged to try to correct the interference by one or more of the following 
measures: 

 

1.

 

Reorient or relocate the receiving antenna. 

 

2.

 

Move the equipment away from the receiver. 

 

3.

 

Plug the equipment into an outlet on a circuit different from that to which the receiver is 

powered. 

 

4.

 

Consult MSKL or an experienced radio/television technician for help. 

 
All external connections should be made using shielded cables. 

 

 

 

 

 
 

 
 

 

 
 

 
 

 

 
 

 
 

 

 
 

 
 

 
 

 

 
 

 

Summary of Contents for MSKL MS-3020














Reviews: