Maktec MT370 Instruction Manual Download Page 7

7

Remove the chip deflector.

Loosen the screws and remove the base protector. Place the templet guide on
the base and replace the base protector. Then secure the base protector by
tightening the screws.

Secure the templet to the workpiece. Place the tool on the templet and move
the tool with the templet guide sliding along the side of the templet.

NOTE:

The workpiece will be cut a slightly different size from the templet. Allow
for the distance (X) between the router bit and the outside of the templet
guide. The distance (X) can be calculated by using the following
equation:

Distance (X) = (outside diameter of the templet guide - router bit diameter) / 2

Straight guide (Accessory)

The straight guide is effectively used for straight cuts when chamfering or
grooving.

Attach the guide plate to the straight guide with the bolt, the wave washer, the
flat washer and the wing nut.

1. Screwdriver

2. Base protector

3. Screws

1

2

3

3

004556

1. Bit

2. Base

3. Templet

4. Workpiece

5. Templet guide

1

2

3

4

5

005435

005436

1. Bolt

2. Guide plate

3. Straight guide

4. Flat washer

5. Wave washer

6. Wing nut

1

2

3

4
5
6

001990

Summary of Contents for MT370

















Reviews: