Maktec MT191, Instruction Manual

Page: 4 / 48

4
ENGLISH (Original instructions)
Explanation of general view
1-1. Pointer
1-2. Knob
2-1. Switch trigger
2-2. Lock button or Lock-off button
3-1. Planer blade
3-2. Rear base
3-3. Foot
4-1. Socket wrench
4-2. Bolts
5-1. Bolts
5-2. Drum
5-3. Planer blade
5-4. Drum cover
5-5. Adjusting plate
6-1. Inside edge of gauge plate
6-2. Blade edge
6-3. Planer blade
6-4. Adjusting plate
6-5. Screws
6-6. Heel 6-7. Back side of gauge base
6-8. Gauge plate
6-9. Gauge base
7-1. Socket wrench
7-2. Bolts
8-1. Screws
8-2. Adjusting plate
8-3. Planer blade locating lugs
8-4. Gauge plate
8-5. Heel of adjusting plate
8-6. Set plate
8-7. Inside flank of gauge plate
8-8. Gauge base
8-9. Back side of gauge base
8-10. Mini planer blade
9-1. Mini planer blade
9-2. Groove
9-3. Set plate
9-4. Bolts
9-5. Drum cover 9-6. Drum
9-7. Adjusting plate
11-1. Start
11-2. End
13-1. Blade edge
13-2. Cutting line
14-1. Screw
14-2. Edge fence (Accessory)
19-1. Sharpening holder
20-1. Wing nut
20-2. Blade (A)
20-3. Blade (B)
20-4. Side (D)
20-5. Side (C)
22-1. Limit mark
23-1. Chip cover or Nozzle
23-2. Screwdriver
24-1. Brush holder cap
24-2. Screwdriver
SPECIFICATIONS
Model MT191
Planing width 82 mm
Planing depth 2 mm
Shiplapping depth 9 mm
No load speed (min
-1
) 16,000
Overall length 285 mm
Net weight 2.7 kg
Safety class /II
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
ENE001-1
Intended use
The tool is intended for planing wood.
ENF002-2
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
ENG905-1
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
pA
) : 85 dB(A)
Sound power level (L
WA
) : 96 dB(A)
Uncertainty (K) : 3 dB(A)
Wear ear protection
ENG900-1
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Work mode : planing softwood
Vibration emission (a
h
) : 3.5 m/s
2
Uncertainty (K) : 1.5 m/s
2
ENG901-1
•
The declared vibration emission value has been
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
•
The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
•
The vibration emission during actual use of the
power tool can differ from the declared emission
value depending on the ways in which the tool is