Maktec MT070 Instruction Manual Download Page 6

ASSEMBLY 

 

CAUTION: 

• 

Always be sure that the tool is switched off and the 
battery cartridge is removed before carrying out 
any work on the tool. 

Installing or removing driver bit or drill bit 

Fig.6 

Hold the ring and turn the sleeve counterclockwise to 
open the chuck jaws. Place the bit in the chuck as far as 
it will go. Hold the ring firmly and turn the sleeve 
clockwise to tighten the chuck. 
To remove the bit, hold the ring and turn the sleeve 
counterclockwise. 

OPERATION 

 

CAUTION: 

• 

Always insert the battery cartridge all the way until 
it locks in place. If you can see the red indicator on 
the upper side of the button, it is not locked 
completely. Insert it fully until the red indicator 
cannot be seen. If not, it may accidentally fall out 
of the tool, causing injury to you or someone 
around you. 

Screwdriving operation 

Fig.7 

CAUTION: 

• 

Adjust the adjusting ring to the proper torque level 
for your work. 

Place the point of the driver bit in the screw head and 
apply pressure to the tool. Start the tool slowly and then 
increase the speed gradually. Release the switch trigger 
as soon as the clutch cuts in. 

 

CAUTION: 

• 

Make sure that the driver bit is inserted straight in 
the screw head, or the screw and/or bit may be 
damaged. 

NOTE: 

• 

When driving wood screws, predrill pilot holes to 
make driving easier and to prevent splitting of the 
workpiece. See the chart. 

Nominal diameter of wood screw 

(mm)

Recommended size of pilot hole 

(mm)

3.1

2.0 - 2.2

3.5

2.2 - 2.5

3.8

2.5 - 2.8

4.5

2.9 - 3.2

4.8

3.1 - 3.4

5.1

3.3 - 3.6

5.5

3.7 - 3.9

5.8

4.0 - 4.2

6.1

4.2 - 4.4

   

006421 

Drilling operation 

First, turn the adjusting ring so that the pointer points to 
the 

  marking. Then proceed as follows. 

Drilling in wood 

When drilling in wood, the best results are obtained with 
wood drills equipped with a guide screw. The guide 
screw makes drilling easier by pulling the bit into the 
workpiece. 

Drilling in metal 

To prevent the bit from slipping when starting a hole, 
make an indentation with a center-punch and hammer 
at the point to be drilled. Place the point of the bit in the 
indentation and start drilling. 
Use a cutting lubricant when drilling metals. The 
exceptions are iron and brass which should be drilled 
dry. 

 

CAUTION: 

• 

Pressing excessively on the tool will not speed up 
the drilling. In fact, this excessive pressure will 
only serve to damage the tip of your bit, decrease 
the tool performance and shorten the service life 
of the tool. 

• 

There is a tremendous force exerted on the tool/bit 
at the time of hole break through. Hold the tool 
firmly and exert care when the bit begins to break 
through the workpiece. 

• 

A stuck bit can be removed simply by setting the 
reversing switch to reverse rotation in order to 
back out. However, the tool may back out abruptly 
if you do not hold it firmly. 

• 

Always secure small workpieces in a vise or 
similar hold-down device. 

• 

If the tool is operated continuously until the battery 
cartridge has discharged, allow the tool to rest for 
15 minutes before proceeding with a fresh battery. 

MAINTENANCE 

 

CAUTION: 

• 

Always be sure that the tool is switched off and the 
battery cartridge is removed before attempting to 
perform inspection or maintenance. 

• 

Never use gasoline, benzine, thinner, alcohol or 
the like. Discoloration, deformation or cracks may 
result. 

To maintain product SAFETY and RELIABILITY, repairs, 
any other maintenance or adjustment should be 
performed by Makita Authorized Service Centers, 
always using Makita replacement parts. 

Summary of Contents for MT070





















































Reviews: