Makita VC011G Instruction Manual Download Page 20

20

ENGLISH

The board is supported by three springs.

If the springs came off from the projections, reattach

them as illustrated.

2

3

1

Fig.48

►    

1.

Long spring 

2.

Short spring 

3.

Projection

NOTE:

 Attach the springs securely so that the springs 

touch the root of the projections.

Attaching the board

1.

Insert the straight side of the board into the 

catches in the lower left side of the room.

2.

Put the right side of the board in place.

2

1

3

Fig.49

►    

1.

Board 

2.

Straight side 

3.

Catch

CYCLONE ATTACHMENT

Optional accessory

NOTE:

 When using the cyclone attachment with this 

appliance, the bent pipe is also required.

1

Fig.50

►    

1.

Cyclone attachment

About the cyclone attachment

Using the cleaner with the cyclone attachment installed 
reduces the amount of dust that enters the dust bag, 
which helps to prevent the suction force from weaken-
ing. In addition, cleaning after use is also simple.

CAUTION:

Always be sure that the tool is 

switched off and the battery cartridge is removed 

before carrying out any work on the tool.

 If the 

battery cartridge is left inserted, the cleaner may start 

unexpectedly and result in injury.

CAUTION:

Clean the mesh filter of the 

cyclone attachment and the dust bag of the 
cleaner unit when they become clogged.

Continued use in the clogged condition may result in 
heating or smoke.

NOTICE:

When the cyclone attachment is 

attached, do not use the cyclone attachment in 
the horizontal or upward facing condition.

 Doing 

so may cause the mesh filter to become clogged.

NOTICE:

Always use the cleaner with the dust 

bag installed, even when using the cyclone 
attachment.

 Using the cleaner without the dust bag 

installed may result in a motor malfunction.

NOTE:

 Check that the cyclone attachment, cleaner, 

and straight pipe are locked properly before use.

NOTE:

 Empty the dust case of the cyclone attach-

ment and the dust bag of the cleaner when dust has 
accumulated. Continued use will result in weakened 
suction force.

NOTE:

 You can use the cyclone attachment with or 

without lock function.

NOTE:

 To install or remove the cyclone attachment, 

refer to the section "Using as a cleaner".

Summary of Contents for VC011G

























Reviews: