11 ENGLISH
For preparation of the item being shipped, consult
-
ing an expert for hazardous material is required.
Please also observe possibly more detailed
national regulations.
Tape or mask off open contacts and pack up the
battery in such a manner that it cannot move
around in the packaging.
11.
When disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
12.
Use the batteries only with the products
specified by Makita.
Installing the batteries to
non-compliant products may result in a fire, exces
-
sive heat, explosion, or leak of electrolyte.
13.
If the tool is not used for a long period of time,
the battery must be removed from the tool.
14.
During and after use, the battery cartridge may
take on heat which can cause burns or low
temperature burns. Pay attention to the han
-
dling of hot battery cartridges.
15.
Do not touch the terminal of the tool imme
-
diately after use as it may get hot enough to
cause burns.
16.
Do not allow chips, dust, or soil stuck into the
terminals, holes, and grooves of the battery
cartridge.
It may cause heating, catching fire,
burst and malfunction of the tool or battery car
-
tridge, resulting in burns or personal injury.
17.
Unless the tool supports the use near
high-voltage electrical power lines, do not use
the battery cartridge near a high-voltage elec
-
trical power lines.
It may result in a malfunction
or breakdown of the tool or battery cartridge.
18.
Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causing fires, personal injury and damage. It will
also void the Makita warranty for the Makita tool and
charger.
Tips for maintaining maximum
battery life
1.
Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2.
Never recharge a fully charged battery car
-
tridge. Overcharging shortens the battery
service life.
3.
Charge the battery cartridge with room tem
-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4.
When not using the battery cartridge, remove
it from the tool or the charger.
5.
Charge the battery cartridge if you do not use
it for a long period (more than six months).
ASSEMBLY
CAUTION:
Always be sure that the machine is
switched off and the battery cartridge is removed
before carrying out any work on the machine.
Assembling blower pipes
1.
Loosen the clamp screw.
►
Fig.1:
1.
Clamp screw
2.
Install the control handle to the swivel pipe and
tighten the clamp screw.
►
Fig.2:
1.
Control handle
2.
Swivel pipe
3.
Clamp screw
NOTICE:
Be careful not to twist the cable of the
control handle when attaching the control handle
to the swivel pipe.
3.
Loosen the screw on the hose clamp, and then
attach the hose clamp to the flexible pipe. Attach the
swivel pipe to the flexible pipe, and then tighten the
screw on the hose clamp.
►
Fig.3:
1.
Swivel pipe
2.
Hose clamp
3.
Flexible pipe
4.
Loosen the screw on the hose clamp, and then attach
the hose clamp to the flexible pipe. Attach the flexible pipe
to the elbow, and then tighten the screw on the hose clamp.
►
Fig.4:
1.
Flexible pipe
2.
Hose clamp
3.
Elbow
NOTICE:
Make sure that the screws on the hose
clamps are facing the direction shown in the figure.
►
Fig.5:
1.
Screw
5.
Clamp the control cable to the cable holders.
►
Fig.6:
1.
Cable holder
2.
Control cable
NOTICE:
Make sure that the control cable is
securely fixed to the cable holders.
Installing the end nozzle
Align the triangle mark on the end nozzle with that on
the swivel pipe, then attach the end nozzle to the swivel
pipe, and then turn the end nozzle to lock it into place.
►
Fig.7:
1.
Triangle mark
2.
End nozzle
3.
Swivel pipe
To remove the end nozzle, perform the installation
procedure in reverse.
NOTE:
The length of the nozzle can be changed by
moving the nozzle as shown in the figure.
►
Fig.8:
1.
End nozzle
2.
Swivel pipe
Installing the flat nozzle or
extension nozzle
Optional accessory
NOTE:
If the end nozzle is installed, remove it before
installing the adapter pipe.
1.
Align the triangle mark on the adapter pipe with
that on the swivel pipe, then attach the adapter pipe to
the swivel pipe, and then turn it to lock it into place.
►
Fig.9:
1.
Triangle mark
2.
Adapter pipe
3.
Swivel
pipe
Summary of Contents for UB002C
