10 ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model:
SP001G
Blade diameter
165 mm
Max. Cutting depth
at 0°
56 mm
at 45° bevel
40 mm
at 48° bevel
38 mm
No load speed
2,500 - 4,900 min
-1
Overall length (with BL4040)
375 mm
Rated voltage
D.C. 36 V - 40 V max
Net weight
4.4 - 5.0 kg
•
Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
•
Specifications and battery cartridge may differ from country to country.
•
The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi
-
est combinations, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
BL4020/BL4025*/BL4040*/BL4050F*
* : Recommended battery
Charger
DC40RA / DC40RB / DC40RC
•
Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING:
Only use the battery cartridges and chargers listed above.
Use of any other battery cartridges
and chargers may cause injury and/or fire.
Intended use
The tool is specially intended for performing plunge
cuts. The tool is also intended for rip and cross cuts in
wood. If the tool is equipped with proper circular saw
blade, the tool can be used for sawing aluminum, plas-
tic, mineral contained plastic, and similar materials.
Noise
The typical A-weighted noise level determined accord
-
ing to EN62841-2-5:
Sound pressure level (L
pA
) : 89 dB(A)
Sound power level (L
WA
) : 100 dB (A)
Uncertainty (K) : 3 dB(A)
NOTE:
The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE:
The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared val
-
ue(s) depending on the ways in which the tool is used
especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-2-5:
Work mode: cutting wood
Vibration emission (a
h,W
) : 2.5 m/s
2
or less
Uncertainty (K) : 1.5 m/s
2
Work mode: cutting metal
Vibration emission (a
h,M
) : 2.5 m/s
2
or less
Uncertainty (K) : 1.5 m/s
2
NOTE:
The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE:
The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
Summary of Contents for SP001G
