Makita RP1801F Instruction Manual Download

Page: 12 / 16

009933

2. Adjusting the depth of cut

•

A small amount of depth of cut can be obtained by

turning this screw with a screwdriver from above

the table. (1.0 mm per a full turn)

•

Turning it clockwise makes the depth of cut greater

and turning it counterclockwise smaller.

009931

MAINTENANCE

CAUTION:

•

Always be sure that the tool is switched off and

unplugged before attempting to perform inspection

or maintenance.

•

Never use gasoline, benzine, thinner, alcohol or

the like. Discoloration, deformation or cracks may

result.

Replacing carbon brushes

001145

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps.

Take out the worn carbon brushes, insert the new ones

and secure the brush holder caps.

009869

After replacing brushes, plug in the tool and break in

brushes by running tool with no load for about 10

minutes. Then check the tool while running and electric

brake operation when releasing the switch trigger. If

electric brake is not working well, ask your local Makita

service center for repair.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers,

always using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

•

These accessories or attachments are

recommended for use with your Makita tool

specified in this manual. The use of any other

accessories or attachments might present a risk of

injury to persons. Only use accessory or

attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

•

Straight & groove forming bits

•

Edge forming bits

•

Laminate trimming bits

•

Straight guide

•

Trimmer guide

•

Guide holder

•

Templet guides

•

Templet guide adapter

•

Lock nut

•

Collet cone 12 mm, 1/2"

•

Collet sleeve 6 mm, 8 mm, 10 mm

•

Collet sleeve 3/8", 1/4"

•

Wrench 24

•

Vacuum head set

1. Brush holder

cap

2. Screwdriver

1. Limit mark

1. Screwdriver

1. Threaded part in

the motor

bracket

Summary of Contents for RP1801F

















Search results

Summary of Contents for RP1801F

Reviews:

Related manuals for RP1801F

Brands by name

Popular brands

Makita RP1801F, Instruction Manual

Search results

Summary of Contents for RP1801F

Reviews:

Related manuals for RP1801F

Brands by name

Popular brands