manualshive.com logo in svg

Makita RBC411U, Technical Information

Share
Download
Makita RBC411U Technical Information Download Page 15

R

epair

P 15/ 15

[4] DISASSEMBLY/ ASSEMBLY

[4]-13. Stop switch

[5] Tightening torque specifications

Fastening for

Crank case assembly (Crank case 1 and Crank case 2) M5x30 Hex socket head bolt (with washer) 

Description

Fastening torque 

(N.m.)

7.5

Cylinder and Crank case assembly

M6x18 Hex socket head bolt

12.5 

Muffler and Cylinder

Insulator and Cylinder

M6x60 Hex socket head bolt 

11.5

M5x25 Hex socket head bolt

(with washer and spring lock washer) 

4.0

M5x22 Hex socket head bolt 

5.0

Plate of Air cleaner assembly and Insulator

Ignition coil and Cylinder

M5x50 Hex socket head bolt

3.5

Recoil starter assembly and Blower housing

M5x14 Pan head screw

(with washer and spring lock washer) 

3.5

Blower housing and Crank case assembly

M5x50 Hex socket head bolt  

3.5

M5x22 Hex socket head bolt (with washer)  

3.5

Cylinder cover and Blower housing

M5x14 Pan head screw

(with washer and spring lock washer) 

3.5

Cylinder cover and Crank case assembly

M5x20 Pan head screw

(with washer and spring lock washer) 

M5x14 Pan head screw

(with washer and spring lock washer) 

3.5

Muffler cover and Cylinder cover

3.5

Spark plug and Cylinder

M14 Spark plug

15.0

Flywheel and Crankshaft assembly

M6x16 Hex socket head bolt (with spring

lock washer)

12.5

Clutch assembly (Clutch shoe and Holder)

M8 Shoulder hex bolt

12.0

Holder of Clutch assembly and Crankshaft assembly

M6x14 Hex head bolt

11.5

Gear case assembly and Pipe shaft complete

M6x30 Hex socket head bolt 

(with washer and spring lock washer) 
M5x12 Hex socket head bolt 

(with washer and spring lock washer) 

8.5

3.0

Clutch drum complete and Shaft complete

M6x14 Hex head bolt

11.0

Hanger and Clutch case complete

M6x28 Hex head bolt 

(with washer and spring lock washer)

8.0

Shaft pipe complete and Holder, Handle ass’y

M6x30 Hex socket head bolt (with washer)

6.0

Stopper and Clutch case complete

M6x35 Pan head screw

5.0

Fig. 57

Check the continuity between the bullet terminals on the two lead wires 

extending from Control lever with a circuit tester. (

Fig. 57

)

If Stop switch functions properly,

there will be no continuity with the switch ON

and there will be continuity with the switch OFF.

Tester

CHECKING STOP SWITCH

Summary of Contents for RBC411U
















Reviews:

No comments

Brands by name

Popular brands

Load more brands