23 ENGLISH
Changing the nozzle
You can change the standard nozzle to the ULV (Ultra
Low Volume) nozzle. The ULV nozzle can discharge
finer mist than the standard nozzle. To change the
nozzle, follow the steps below.
1.
Loosen the screw and remove it, and then remove
the front side of the end nozzle.
►
Fig.38:
1.
Screw
2.
End nozzle
2.
Remove the standard nozzle by turning the nozzle
counterclockwise using the wrench.
►
Fig.39:
1.
Wrench
2.
Standard nozzle
3.
Remove the O-ring from the standard nozzle, and
then attach it to the ULV nozzle.
►
Fig.40:
1.
O-ring
2.
Standard nozzle
3.
ULV nozzle
4.
Attach the ULV nozzle by turning the nozzle clock
-
wise using the wrench.
►
Fig.41:
1.
Wrench
2.
ULV nozzle
NOTICE:
Do not tighten the nozzle too much.
The recommended tightening torque is approxi-
mately 1.0 N•m.
Tightening the nozzle too much may
damage the mounting part for nozzle.
5.
Attach the end nozzle, and then tighten the screw.
►
Fig.42:
1.
Screw
2.
End nozzle
TROUBLESHOOTING
Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the man
-
ual, do not attempt to dismantle the machine. Instead, ask Makita Authorized Service Centers, always using Makita
replacement parts for repairs.
State of abnormality
Probable cause (malfunction)
Remedy
Motor does not run.
Battery is not installed.
Install the battery.
Battery problem (under voltage)
Recharge the battery. If recharging is not effective,
replace battery.
The drive system does not work
correctly.
Ask your local authorized service center for repair.
Motor stops running after a little use. Battery's charge level is low.
Recharge the battery. If recharging is not effective,
replace battery.
Overheating.
Stop using the machine to allow it to cool down.
Mist is not discharged.
Tank is empty.
Fill the tank with liquid.
Nozzle lever or tank lever is closed.
Open the nozzle lever and tank lever.
Nozzle is clogged.
Remove the standard nozzle or ULV nozzle, and
then clean the nozzle with running water to remove
the clogged material.
Filter is clogged.
Remove the filter, and then clean the filter with
running water to remove the clogged material.
The machine does not reach the
maximum speed.
Battery is installed improperly.
Install the battery as described in this manual.
Battery power is dropping.
Recharge the battery. If recharging is not effective,
replace battery.
The drive system does not work
correctly.
Ask your local authorized service center for repair.
Abnormal vibration:
stop the machine immediately!
The drive system does not work
correctly.
Ask your local authorized service center for repair.
Motor cannot stop:
Remove the battery immediately!
Electric or electronic malfunction.
Remove the battery and ask your local authorized
service center for repair.
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita prod-
uct specified in this manual.
The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
•
Deflector
•
Makita genuine battery and charger
NOTE:
Some items in the list may be included in the
product package as standard accessories. They may
differ from country to country.
Summary of Contents for PM001G
