manualshive.com logo in svg

Makita PC5001C, Technical Information, Page: 9 / 9

Share
Download
Makita PC5001C Technical Information Download Page 9

  

P 

9

/ 

9

W

iring diagram

Wiring in Motor Housing

Wiring in Handle

Fig. D-4

Fig. D-5

Pick-up Coil

Put Controller’s lead wire and Field’s
Lead wire as illustrated below.

Grip

Brush holder

Pull out Field lead wires (orange and white) from the illustrated opening of Motor housing.

Brush holder

Makita
logo side

Field lead wire
(white)

Field lead wire
(orange)

Controller’s
Lead wire (orange)

Switch Lever

Switch Lever

Field’s
Lead wire 
(orange)

Controller’s
Lead wire (black)

Controller’s
Lead wire (red, or blue)

Wiring under Switch

Controller
side

Controller

Switch lever side

Wiring to Switch

(viewing from Handle set (L) side)

(viewing from Handle set (R) side)

Handle

Switch

Noise suppressor

Terminal block

Insulated

Connector

Fix Field lead wires (orange, white)
with this Lead wire holder.  

Pass Field lead wires (orange, white)
between Handle set and Controller setting rib.  

Pass Pick-up coil’s  lead wires (black, white) between Handle set
and Controller setting rib.  

Fix Controller’s lead wires (black,
orange, red, white) with this Lead 
wire holder.  

Summary of Contents for PC5001C










Reviews:

No comments