4
ENGLISH
(Original instructions)
Explanation of general view
1
Lever
2
Wing nut
3
Bevel scale plate
4
Base plate
5
Cutting line
6
Lock button/Lock-off button
7
Switch trigger
8
Shaft lock
9
Wrench
10
Hex bolt
11
Saw blade
12
Outer flange
1
3
Inner flange
14
Side grip
15 Rear handle
16 Front grip
17 Base
1
8
Guide rule
19 Limit mark
20 Brush holder cap
21 Screwdriver
SPECIFICATIONS
Model
N5900B
Blade diameter .................................................... 2
3
5 mm
Max. cutting depth
at 90° .................................................................
8
5 mm
at 45° ................................................................. 60 mm
at 50° ................................................................. 5
3
mm
No load speed (min
–1
) ............................................ 4,100
Overall length ......................................................
38
0 mm
Net weight ............................................................. 6.7 kg
Safety class .............................................................
/II
• Due to our continuing program of research and
development, the specifications herein are subject to
change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2014
ENE02
8
-1
Intended use
The tool is intended for performing lengthways and
crossways straight cuts and mitre cuts with angles in
wood while in firm contact with the workpiece.
ENF002-2
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
ENF100-1
For public low-voltage distribution systems of
between 220 V and 250 V.
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under unfavor-
able mains conditions can have adverse effects to the
operation of other equipment. With a mains impedance
equal or less than 0.
3
1 Ohms it can be presumed that
there will be no negative effects. The mains socket used
for this device must be protected with a fuse or protective
circuit breaker having slow tripping characteristics.
GEA010-2
General power tool safety warnings
WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool.
Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future refer-
ence.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
GEB1
33
-2
CIRCULAR SAW SAFETY WARNINGS
Cutting procedures
1.
DANGER: Keep hands away from cutting area
and the blade. Keep your second hand on auxil-
iary handle, or motor housing.
If both hands are
holding the saw, they cannot be cut by the blade.
2.
Do not reach underneath the workpiece.
The
guard cannot protect you from the blade below the
workpiece.
3.
Adjust the cutting depth to the thickness of the
workpiece.
Less than a full tooth of the blade teeth
should be visible below the workpiece.
4.
Never hold the workpiece in your hands or
across your leg while cutting. Secure the work-
piece to a stable platform.
It is important to sup-
port the work properly to minimise body exposure,
blade binding, or loss of control.
000157
5.
Hold the power tool by insulated gripping sur-
faces, when performing an operation where the
cutting tool may contact hidden wiring or its own
cord.
Contact with a “live” wire will also make
exposed metal parts of the power tool “live” and
could give the operator an electric shock.
6.
When ripping, always use a rip fence or straight
edge guide.
This improves the accuracy of cut and
reduces the chance of blade binding.
7.
Always use blades with correct size and shape
(diamond versus round) of arbour holes.
Blades
that do not match the mounting hardware of the saw
will run off-centre, causing loss of control.
8.
Never use damaged or incorrect blade washers
or bolt.
The blade washers and bolt were specially
designed for your saw, for optimum performance and
safety of operation.
