background image

10 

MAINTENANCE 

 

CAUTION: 

• 

Always be sure that the tool is switched off and 
unplugged before attempting to perform inspection 
or maintenance. 

• 

Never use gasoline, benzine, thinner, alcohol or 
the like. Discoloration, deformation or cracks may 
result. 

1

2

 

 

011107 

The tool and its air vents have to be kept clean. 
Regularly clean the tool's air vents or whenever the 
vents start to become obstructed. 

Replacing carbon brushes 

1

2

3

 

 

001146 

When the resin insulating tip inside the carbon brush is 
exposed to contact the commutator, it will automatically 
shut off the motor. When this occurs, both carbon 
brushes should be replaced. Keep the carbon brushes 
clean and free to slip in the holders. Both carbon 
brushes should be replaced at the same time. Use only 
identical carbon brushes. 
Use a screwdriver to remove the brush holder caps. 
Take out the worn carbon brushes, insert the new ones 
and secure the brush holder caps. 

1

2

 

 

011106 

 

To maintain product SAFETY and RELIABILITY, repairs, 
any other maintenance or adjustment should be 
performed by Makita Authorized Service Centers, 
always using Makita replacement parts. 

1. Brush holder 

cap 

2. Screwdriver 

1. Commutator 
2. Insulating tip 
3. Carbon brush 

1. Exhaust vent 
2. Inhalation vent

Summary of Contents for M9001













Reviews: