background image

   

015286 

Chipping/Scaling/Demolition 

Hold the tool firmly with both hands. Turn the tool on 
and apply slight pressure on the tool so that the tool will 
not bounce around, uncontrolled. Pressing very hard on 
the tool will not increase the efficiency. 

MAINTENANCE 

 

CAUTION: 

• 

Always be sure that the tool is switched off and 
unplugged before attempting to perform inspection 
or maintenance. 

• 

Never use gasoline, benzine, thinner, alcohol or 
the like. Discoloration, deformation or cracks may 
result. 

Replacing carbon brushes 

1

2

3

 

 

001146 

When the resin insulating tip inside the carbon brush is 
exposed to contact the commutator, it will automatically 
shut off the motor. When this occurs, both carbon 
brushes should be replaced. Keep the carbon brushes 
clean and free to slip in the holders. Both carbon 
brushes should be replaced at the same time. Use only 
identical carbon brushes. 

2

1

 

 

015231 

Use a screwdriver to remove the rear cover. 

2

1

 

 

015232 

Use a screwdriver to remove the brush holder caps. 
Take out the worn carbon brushes, insert the new ones 
and secure the brush holder caps. 
 
 
To maintain product SAFETY and RELIABILITY, repairs, 
any other maintenance or adjustment should be 
performed by Makita Authorized Service Centers, 
always using Makita replacement parts. 

1. Screwdriver 
2. Brush holder 

cap 

1. Screwdriver 
2. Rear cover 

1. Commutator 
2. Insulating tip 
3. Carbon brush 

Summary of Contents for M8600G









Reviews: