background image

38 ENGLISH

Cancelling tool registration for the 

vacuum cleaner

Perform the following procedure when cancelling the 

tool registration for the vacuum cleaner.

1.

  Install the batteries to the vacuum cleaner and the 

tool.

2.

  Set the stand-by switch on the vacuum cleaner to 

"AUTO".

1

►    

1.

 Stand-by switch

3.

  Press the wireless activation button on the vac-

uum cleaner for 6 seconds. The wireless activation 

lamp blinks in green and then become red. After that, 

press the wireless activation button on the tool in the 

same way.

1

1

2

2

►    

1.

 Wireless activation button 

2.

 Wireless activation 

lamp

If the cancellation is performed successfully, the wire-

less activation lamps will light up in red for 2 seconds 

and start blinking in blue.

NOTE:

 The wireless activation lamps finish blinking in 

red after 20 seconds elapsed. Press the wireless acti-

vation button on the tool while the wireless activation 

lamp on the cleaner is blinking. If the wireless acti-

vation lamp does not blink in red, push the wireless 

activation button briefly and hold it down again.

Summary of Contents for LS004GD201













































Reviews: