Makita LS004GD201 Instruction Manual Download Page 12

Page: 12 / 44

12 ENGLISH

This tool should be bolted with four bolts to a level and

stable surface using the bolt holes provided in the tool's

base. This will help prevent tipping and possible injury.

►

Bolts

WARNING:

Ensure that the tool will not move

on the supporting surface.

Movement of the miter

saw on the supporting surface while cutting may

result in loss of control and serious personal injury.

FUNCTIONAL

DESCRIPTION

WARNING:

Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking the functions on

the tool.

Failure to switch off and remove the battery

cartridge may result in serious personal injury from

accidental start-up.

Installing or removing battery

cartridge

CAUTION:

Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION:

Hold the tool and the battery car-

tridge firmly when installing or removing battery

cartridge.

Failure to hold the tool and the battery

cartridge firmly may cause them to slip off your hands

and result in damage to the tool and battery cartridge

and a personal injury.

►

Red indicator

Button

Battery cartridge

To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator as

shown in the figure, it is not locked completely.

CAUTION:

Always install the battery cartridge

fully until the red indicator cannot be seen.

If not,

it may accidentally fall out of the tool, causing injury to

you or someone around you.

CAUTION:

Do not install the battery cartridge

forcibly.

If the cartridge does not slide in easily, it is

not being inserted correctly.

Tool / battery protection system

The tool is equipped with a tool/battery protection sys-

tem. This system automatically cuts off power to the

motor to extend tool and battery life. The tool will auto-

matically stop during operation if the tool or battery is

placed under one of the following conditions.

Overload protection

When the tool/battery is operated in a manner that

causes it to draw an abnormally high current, the tool

automatically stops. In this situation, turn the tool off

and stop the application that caused the tool to become

overloaded. Then turn the tool on to restart.

Overheat protection

When the tool/battery is overheated, the tool stops

automatically and the lamp will blink. In this situation, let

the tool cool down before turning the tool on again.

Summary of Contents for LS004GD201













































Search results

Summary of Contents for LS004GD201

Reviews:

Related manuals for LS004GD201

Brands by name

Popular brands

Makita LS004GD201, Instruction Manual

Search results

Summary of Contents for LS004GD201

Reviews:

Related manuals for LS004GD201

Brands by name

Popular brands