background image

9 ENGLISH

To remove the battery cartridge, slide it from the tool 

while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the 

battery cartridge with the groove in the housing and slip 

it into place. Insert it all the way until it locks in place 

with a little click. If you can see the red indicator as 

shown in the figure, it is not locked completely.

CAUTION:

 

Always install the battery cartridge 

fully until the red indicator cannot be seen.

 If not, 

it may accidentally fall out of the tool, causing injury to 

you or someone around you.

CAUTION:

 

Do not install the battery cartridge 

forcibly.

 If the cartridge does not slide in easily, it is 

not being inserted correctly.

Tool / battery protection system

The tool is equipped with a tool/battery protection sys-

tem. This system automatically cuts off power to the 

motor to extend tool and battery life. The tool will auto-

matically stop during operation if the tool or battery is 

placed under one of the following conditions.

Overload protection

When the tool/battery is operated in a manner that 

causes it to draw an abnormally high current, the tool 

automatically stops. In this situation, turn the tool off 

and stop the application that caused the tool to become 

overloaded. Then turn the tool on to restart.

Overheat protection

When the tool/battery is overheated, the tool stops 

automatically. In this situation, let the tool cool down 

before turning the tool on again.

NOTE:

 When the tool is overheated, the lamp blinks.

Overdischarge protection

When the battery capacity becomes low, the tool stops 

automatically. If the product does not operate even 

when the switches are operated, remove the batteries 

from the tool and charge the batteries.

Protections against other causes

Protection system is also designed for other causes 

that could damage the tool and allows the tool to stop 

automatically. Take all the following steps to clear the 

causes, when the tool has been brought to a temporary 

halt or stop in operation.
1.  Turn the tool off, and then turn it on again to 

restart.

2.  Charge the battery(ies) or replace it/them with 

recharged battery(ies).

3.  Let the tool and battery(ies) cool down.
If no improvement can be found by restoring protection 

system, then contact your local Makita Service Center.

Indicating the remaining battery capacity

Press the check button on the battery cartridge to indicate the remain-

ing battery capacity. The indicator lamps light up for a few seconds.

1

2

Fig.8

►    

1.

 Indicator lamps 

2.

 Check button

Indicator lamps

Remaining 

capacity

Lighted

Off

Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the 

battery.

The battery 

may have

malfunctioned.

NOTE:

 Depending on the conditions of use and the ambient tem-

perature, the indication may differ slightly from the actual capacity.

NOTE:

 The first (far left) indicator lamp will blink when 

the battery protection system works.

Switch action

WARNING:

 

Before installing the battery car-

tridge into the tool, always check to see that the 

switch trigger actuates properly and returns to 

the "OFF" position when released.

WARNING:

 

NEVER defeat the lock-off button 

by taping down or some other means.

 A switch with 

a negated lock-off button may result in unintentional 

operation and serious personal injury.

WARNING:

 

NEVER use the tool if it runs when 

you simply pull the switch trigger without press-

ing the lock-off button.

 A switch in need of repair 

may result in unintentional operation and serious 

personal injury. Return tool to a Makita service center 

for proper repairs BEFORE further usage.

Summary of Contents for HS011GZ

























Reviews: