background image

P 4 / 20 

[3] DISASSEMBLY/ASSEMBLY
[3] -1. Chuck Section

R

epair

DISASSEMBLE

ASSEMBLE

Do the reverse step of disassembling.  Refer to the illustrations from Fig. 2 to Fig. 9.

[3] -2. Tool Holder Section and Barrel Complete

Pull off Barrel complete, while pushing Impact bolt
with Screwdriver toward Piston in Slide sleeve
so that the Impact bolt remains in the Slide sleeve. 

1) In case of HR4002, it is not necessary to disassemble Chuck section, when repairing inside of Tool holder section.
    Remove Barrel complete together with Chuck section.   (Fig. 10)     Now Impact bolt comes into your sight.
2) Check whether Fluoride ring 25 is worn out.
     When O ring 20 (orange color) under Fluoro carbon resin ring 25 can be seen, Fluoride ring 25 is worn out. (Fig. 11)
     Be sure to replace not only Fluoride ring 25 but also O ring 20 and X ring 18.
3) Check whether there has been dust in the Tool holder. If yes, be sure to clean up Tool holder.

4) For removing Flat washer 45 and Urethane ring 45 from Tool holder, chuck section has to be disassembled as
    illustrated in page 3
.
5) Disassemble Tool holder from Barrel complete, by striking it with plastic hammer.   (Fig. 12)
6) Remove Urethane ring 45 and Flat washer 45 by pushing them toward the Bit installing side of Tool holder.  (Fig. 13)

Screwdriver 

Hex socket head
bolt M6x30: 4 pcs.

Urethane ring 45 

Flat washer 45 

Tool holder

Barrel 

Impact bolt

Impact bolt

Slide sleeve

Fig. 10

Fig. 11

O ring 20
(orange color)

X ring 18

Worn Fluoride ring 25

Flat washer 45

Flat washer 45

Urethane ring 45

Urethane ring 45

Tool holder

Tool holder

Barrel complete

Fig. 12

Fig. 13

Summary of Contents for HR4002





















Reviews: