background image

P 1

2

/ 2

2

[3] DISASSEMBLY/ASSEMBLY

[3]-5. Torque limiter section

R

epair

DISASSEMBING

(1) Remove Bit holder section (HR2610, HR2611F) / Holder section (HR2610T, HR2611FT). 

(2) Remove Change lever section.

(3) Separate Gear housing complete from Motor housing complete.

(4) Remove Tool holder complete (HR2610, HR2611F) / Tool holder guide complete 

      (HR2610T, HR2611FT) by tapping the top as drawn in 

Fig. 31

.

Note

: Flat washer 30 is located between Tool holder (guide) complete and Inner housing 

          complete. Be careful not to lose it.

(5) Set 1R045 and 1R369 to Tool holder (guide) complete. (

Fig. 32

)

(6) Compress Compression spring 32 (

Fig. 33

), then separate Spiro lock washer 30 from 

      Tool holder (guide) complete by sliding a thin slotted screwdriver from the upper end

      as drawn in 

Fig. 34

. The components are disassembled. (

Fig. 35

)

Fig. 33

Fig. 32

Fig. 34

Fig. 37

Fig. 31

Spiro lock washer 30

Tool holder 

(guide) 

complete

Steel ball 4

(4 pcs.)

Pin 6

(6 pcs.)

Driving flange

Compression spring 31

Tool holder 

(guide) complete

Spur gear 51

1R045

Compression spring 31

1R369

Tool holder (guide) complete

1R369

1R369

Upper end of

Spiro lock

washer 30

Flat washer 30 (thicker than the others) Flat washer 30 (thin)

thin 

slotted 

screwdriver

Summary of Contents for HR2610























Reviews: