background image

C

ircuit diagram

C

ircuit diagram

Fig. D-3

Fig. D-4

Replacement of LED Light Circuit

LED Light circuit can be singly replaced, separating from Controller.

1. Cut the lead wires to the proper 

    length, so that Non-insulated 

    sleeves can be put to the space 

    between Switch and Stator.

    And twist the wires.

2. Pass lead wires through Non-

    insulated sleeves.  

    And then, coat the Non-insulated 

    sleeves with Poly  olefin tubes.

3. Press Non-insulated sleeves coated with 

    Poly olefin tubes.

    So, the fresh LED light circuit is connected 

    to the lead wires of Controller.

Controller

Controller

Twisted wire

Twisted wire

Non-insulated

sleeve

Poly olefin 

tube

at least 2 mm

Non insulated

sleeve

Non insulated sleeve

Wiring of Replaced LED light circuit

edge of Poly olefin tube

edge of Poly olefin tube

2. Cut Poly olefin tube at

    least 4mm longer than 

    Non insulated sleeve.

1. Use Poly olefin tube of

    which Inner diameter is 

    4mm, for coating Non-

    insulated sleeve.

at least 2 mm

Press

Press

Press

Rib B

Stator

< Note >

The lead wire of LED light circuit

have to be put under Stator’s lead 

wires (orange), (white), (blue).

Put Non-insulated sleeves coated with

Poly olefin tube, to the illustrated area

designated with gray color.

P 20/ 20 

Summary of Contents for HP332D





















Reviews: