background image

2

SPECIFICATIONS

• Manufacturer reserves the right to change specifications without notice.

• Specifications may differ from country to country.

GENERAL SAFETY RULES

USA002-2

(For All Tools)

WARNING:

Read and understand all instructions.

 Failure to follow all

instructions listed below, may result in electric shock, fire and/or
serious personal injury.

SAVE THESE INSTRUCTIONS

Work Area

1.

Keep your work area clean and well lit.

Cluttered benches and dark areas invite acci-
dents.

2.

Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases, or dust.

 Power

tools create sparks which may ignite the dust
or fumes.

3.

Keep bystanders, children, and visitors
away while operating a power tool.

 Distrac-

tions can cause you to lose control.

Model

HP2010N

Speed

High

Low

Capacities

Concrete

13 mm (1/2”)

20 mm (3/4”)

Steel

6.5 mm (1/4”)

13 mm (1/2”)

Wood

20 mm (3/4”)

40 mm (1-1/2”)

No load speed (RPM)

0 - 2,300/min.

0 - 900/min.

Blows per minute

0 - 46,000

0 - 18,000

Overall length

350 mm (13-3/4”)

Net weight

3.0 kg (6.6 lbs)

Summary of Contents for HP2010N

















Reviews: