background image

ENGLISH (Original instructions) 

SPECIFICATIONS 

Model HP1640/HP1640F/HP1641/HP1641F 

Concrete 16 

mm 

Steel 13 

mm 

Capacities 

Wood 30 

mm 

No load speed (min

-1

0 - 2,800 

Blows per minute 

0 - 44,800 

Overall length 

303 mm 

Net weight 

2.0 kg 

Safety class 

/II 

• Due to our continuing program of research and development, the specifications herein are subject to change without notice. 
• Specifications may differ from country to country. 
• Weight according to EPTA-Procedure 01/2003 

 

END201-5 

 

Symbols 

The following show the symbols used for the equipment. 
Be sure that you understand their meaning before use. 

  Read instruction manual. 

 

 DOUBLE 

INSULATION 

 

  Only for EU countries 

Do not dispose of electric equipment 
together with household waste material! 
In observance of European Directive 
2002/96/EC on waste electric and 
electronic equipment and its 
implementation in accordance with 
national law, electric equipment that 
have reached the end of their life must 
be collected separately and returned to 
an environmentally compatible 
recycling facility. 

ENE039-1 

Intended use

 

The tool is intended for impact drilling in brick, concrete 
and stone as well as for drilling without impact in wood, 
metal, ceramic and plastic. 

ENF002-1 

Power supply

 

The tool should be connected only to a power supply of 
the same voltage as indicated on the nameplate, and 
can only be operated on single-phase AC supply. They 
are double-insulated in accordance with European 
Standard and can, therefore, also be used from sockets 
without earth wire. 

 
 
 
 
 

For Model HP1640,HP1641,HP1641F 

ENG102-3 

Noise

 

The typical A-weighted noise level determined according 
to EN60745: 

Sound pressure level (L

pA

) : 92 dB (A) 

Sound power level (L

WA

) : 103 dB (A) 

Uncertainty (K) : 3 dB (A) 

Wear ear protection 

ENG203-2 

Vibration 

The vibration total value (tri-axial vector sum) 
determined according to EN60745: 

Work mode: impact drilling into concrete 
Vibration emission (a

h,ID

) : 19 m/s

Uncertainty (K) : 2.0 m/s

ENG301-1 

Work mode : drilling into metal 
Vibration emission (a

h,D

) : 2.5 m/s

Uncertainty (K) : 1.5 m/s

ENG901-1 

• 

The declared vibration emission value has been 
measured in accordance with the standard test 
method and may be used for comparing one tool 
with another. 

• 

The declared vibration emission value may also be 
used in a preliminary assessment of exposure. 

 

WARNING: 

• 

The vibration emission during actual use of the 
power tool can differ from the declared emission 
value depending on the ways in which the tool is 
used. 

• 

Be sure to identify safety measures to protect the 
operator that are based on an estimation of 
exposure in the actual conditions of use (taking 
account of all parts of the operating cycle such as 
the times when the tool is switched off and when it 
is running idle in addition to the trigger time). 

Summary of Contents for HP1640K









Reviews: