![background image](http://html.mh-extra.com/html/makita/hm0860c/hm0860c_instruction-manual_229266005.webp)
5
ENGLISH
Explanation of general view
1
Switch lever
2
Adjusting dial
3
Power-ON indicator lamp
(green)
4
Service indicator lamp ( red )
5
Side grip
6
Side handle
7
Can be swung 360° on the
vertical and secured at any
desired position
8
Secures at eight different
positions back and forth
on the horizontal
9
Clamp nut
10
Loosen
11
Tighten
12
Bit
13
Chuck cover
14
Commutator
15
Insulating tip
16
Carbon brush
17
Screwdriver
18
Brush holder cover
19
Brush holder cap
20
Screw
21
Terminal
22
Crank cap
23
Hammer grease
SPECIFICATION
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for chiselling work in concrete, brick,
stone and asphalt as well as for driving and compacting
with appropriate accessories.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
SPECIFIC SAFETY RULES
GEB004-2
DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to hammer
safety rules. If you use this tool unsafely or incorrectly,
you can suffer serious personal injury.
1.
Wear ear protectors. Exposure to noise can cause
hearing loss.
2.
Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3.
Hold tools by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord. Con-
tact with a “live” wire will make exposed metal parts
of the tool “live” and shock the operator.
4.
Wear a hard hat (safety helmet), safety glasses
and/or face shield. Ordinary eye or sun glasses
are NOT safety glasses. It is also highly recom-
mended that you wear a dust mask and thickly
padded gloves.
5.
Be sure the bit is secured in place before opera-
tion.
6.
Under normal operation, the tool is designed to
produce vibration. The screws can come loose
easily, causing a breakdown or accident. Check
tightness of screws carefully before operation.
7.
In cold weather or when the tool has not been
used for a long time, let the tool warm up for a
while by operating it under no load. This will
loosen up the lubrication. Without proper warm-
up, hammering operation is difficult.
8.
Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
9.
Hold the tool firmly with both hands.
10. Keep hands away from moving parts.
11. Do not leave the tool running. Operate the tool
only when hand-held.
12. Do not point the tool at any one in the area when
operating. The bit could fly out and injure some-
one seriously.
13. Do not touch the bit or parts close to the bit
immediately after operation; they may be
extremely hot and could burn your skin.
14. Do not operate the tool at no-load unnecessarily.
15. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
Model
HM0860C
Blows per minute (min
–1
)
1,100 – 2,650
Overall length
454 mm
Net weight
4.7 kg
Safety class
/II