![background image](http://html.mh-extra.com/html/makita/gau01/gau01_instruction-manual_229187006.webp)
6 ENGLISH
11.
Do not touch the head of the tool.
The head of
the tool becomes hot during operation.
12.
Take a rest to prevent loss of control caused
by fatigue.
We recommend to take a 10 to
20-minute rest every hour.
13.
When you leave the tool, even if it is a short
time, always switch off the tool and remove the
battery cartridge.
The running and unattended
tool may be used by unauthorized person and
cause serious accident.
14.
When operating the tool, do not raise your
right hand above your shoulder height.
15.
During operation, never hit the saw chain
against hard obstacles such stones and nails.
Take particular care when cutting branches
next to walls, wire fences or the like.
16.
If branches get caught in the tool, always stop the
tool and remove the battery cartridge.
Otherwise
unintentional start may cause serious injury.
17.
If the saw chain becomes clogged, always
switch off the tool and remove the battery
cartridge before cleaning.
18.
Accelerating the tool with the saw chain
blocked increases the load and will damage
the tool.
19.
Before cutting limbs, keep an escape area
away from the falling limb. First, clear
obstructs such as limbs and branches from
the work area. Move all tools and goods from
the escape area to another safe place.
20.
Before cutting branches and limbs, check
the falling direction of them, considering the
condition of branches and limbs, adjoining
trees, wind direction, etc. Pay full attention to
the falling direction, and the rebound of the
branch, which hit the ground.
21.
Never hold the tool at an angle of more than
60°. Otherwise falling objects can hit the oper-
ator and cause serious injury. Never stand
underneath the limb being cut.
22.
Pay attention to broken or bent branches.
They
may bounce back in cutting, causing unexpected
injury.
23.
Before cutting limbs that you intend to cut,
remove branches and leaves around them.
Otherwise the saw chain may be caught by them.
24.
To prevent the saw chain from being caught in
the kerf, do not release the lever before pulling
the saw chain out of the kerf.
25.
If the saw chain is bound in the kerf, immedi-
ately stop the tool, carefully move the branch
to open the kerf and release the saw chain.
26.
Avoid kickback (rotational reactive force
towards the operator). To prevent kickback,
never use the guide bar nose or perform a
penetrating cut. Always beware of the position
of the guide bar nose.
27.
Check the chain tension frequently. When
checking or adjusting the chain tension,
switch off the tool and remove the battery
cartridge. If the tension is loose, tighten it.
28.
When you use the tool on muddy ground, wet
slope, or slippery place, pay attention to your
footing.
29.
Do not submerge the tool into a puddle.
30.
Do not leave the tool unattended outdoors in
the rain.
Transport
1.
Before transporting the tool, switch off the tool
and remove the battery cartridge. Always fit
the guide bar cover during transportation.
2.
When transporting the tool, carry it in a hori-
zontal position by holding the grip.
Maintenance
1.
Have your equipment serviced by our autho-
rized service center, always using only genu-
ine replacement parts.
Incorrect repair and poor
maintenance can shorten the life of the tool and
increase the risk of accidents.
2.
Before doing any maintenance or repair work
or cleaning the tool, always switch off the tool
and remove the battery cartridge. Wait until the
tool cools down.
3.
Always wear protective gloves when handling
the saw chain.
4.
After each use, tighten all screws and nuts,
except for adjustment screws.
5.
Keep the saw chain sharp. If the saw chain
has become blunt and cutting performance is
poor, ask Makita authorized service center to
sharpen it or replace it with new one.
6.
Do not attempt any maintenance or repair
not described in this instruction manual. Ask
Makita authorized service center for such
work.
7.
Always use Makita genuine spare parts and
accessories only.
Using parts or accessories
supplied by a third party may result in the tool
breakdown, property damage and/or serious
injury.
Battery tool use and care
1.
Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to battery pack, picking up or carrying the
machine.
Carrying the machine with your finger
on the switch or energizing machine that have the
switch on invites accidents.
2.
Disconnect the battery pack from the machine
before making any adjustments, changing
accessories, or storing machine.
Such preven-
tive safety measures reduce the risk of starting the
machine accidentally.
3.
Recharge only with the charger specified by
the manufacturer.
A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
4.
Use machines only with specifically desig
-
nated battery packs.
Use of any other battery
packs may create a risk of injury and fire.
5.
When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another.
Shorting the battery termi-
nals together may cause burns or a fire.