background image

2 ENGLISH

SPECIFICATIONS

Model:

GA048G

GA049G

GA050G

GA051G

Applicable grinding wheel

Max. wheel diameter

100 mm

115 mm

125 mm

150 mm

Max. wheel thickness

6.4 mm

7.2 mm

6.4 mm

Applicable cut-off wheel

Max. wheel diameter

105 mm

115 mm

125 mm

150 mm

Max. wheel thickness

3.2 mm

3.0 mm

Applicable wire wheel brush

Max. wheel diameter

100 mm

115 mm

125 mm

Max. wheel thickness

20 mm

Spindle thread

M10

M14 or 5/8″ (country specific)

Max. spindle length

18 mm

23 mm

No load speed (n

0

) / Rated speed (n)

11,000 min

-1

9,000 min

-1

Overall length (with BL4040)

410 mm

Net weight

2.8 - 5.2 kg

3.0 - 5.4 kg

3.1 - 4.7 kg

Rated voltage

D.C. 36 V - 40 V max

• 

Due to our continuing program of research and development, the specifications herein are subject to change 

without notice.

• 

Specifications may differ from country to country.

• 

The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi

-

est combinations, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge and charger

Battery cartridge

BL4020 / BL4025* / BL4040* / BL4050F* / BL4080F

* : Recommended battery

Charger

DC40RA / DC40RB / DC40RC

• 

Some of the battery cartridges and chargers listed above may not be available depending on your region of 

residence.

WARNING:

 

Only use the battery cartridges and chargers listed above.

 Use of any other battery cartridges 

and chargers may cause injury and/or fire.

Recommended cord connected power source

Portable power pack

PDC01 / PDC1200

• 

The cord connected power source(s) listed above may not be available depending on your region of residence.

• 

Before using the cord connected power source, read instruction and cautionary markings on them.

Symbols

The followings show the symbols which may be used 

for the equipment. Be sure that you understand their 

meaning before use.

 

Read instruction manual.

Wear safety glasses.

Always operate with two hands.

Do not use the wheel guard for cut-off 

operations.

 

Ni-MH

Li-ion

Only for EU countries

Due to the presence of hazardous com-

ponents in the equipment, waste electrical 

and electronic equipment, accumulators 

and batteries may have a negative impact 

on the environment and human health.

Do not dispose of electrical and electronic 

appliances or batteries with household 

waste!

In accordance with the European Directive 

on waste electrical and electronic equip-

ment and on accumulators and batteries 

and waste accumulators and batteries, 

as well as their adaptation to national law, 

waste electrical equipment, batteries and 

accumulators should be stored separately 

and delivered to a separate collection point 

for municipal waste, operating in accor-

dance with the regulations on environmen-

tal protection.

This is indicated by the symbol of the 

crossed-out wheeled bin placed on the 

equipment.

Summary of Contents for GA048G

























Reviews: