background image

13 ENGLISH

Installing or removing depressed 

center wheel or flap disc

Optional accessory

WARNING:

 

When using a depressed center 

wheel or flap disc, the wheel guard must be fitted 

on the tool so that the closed side of the guard 

always points toward the operator.

WARNING:

 

Make sure that the mounting part 

of the inner flange fits into the inner diameter of 

the depressed center wheel / flap disc perfectly.

 

Mounting the inner flange on the wrong side may 

result in the dangerous vibration.

Mount the inner flange onto the spindle.

Make sure to fit the dented part of the inner flange onto 

the straight part at the bottom of the spindle.

Fit the depressed center wheel / flap disc on the inner 

flange and screw the lock nut onto the spindle.

2
3

4

1

Fig.10

►    

1.

 Lock nut 

2.

 Depressed center wheel 

3.

 Inner 

flange 

4.

 Mounting part

To tighten the lock nut, press the shaft lock firmly so 

that the spindle cannot revolve, then use the lock nut 

wrench and securely tighten clockwise.

1

2

Fig.11

►    

1.

 Lock nut wrench 

2.

 Shaft lock

To remove the wheel, follow the installation procedure 

in reverse.

Installing or removing flex wheel

Optional accessory

WARNING:

 

Always use supplied guard when 

flex wheel is on the tool.

 Wheel can shatter during 

use and guard helps to reduce chances of personal 

injury.

1

2

3

4

Fig.12

►    

1.

 Lock nut 

2.

 Flex wheel 

3.

 Back up pad 

4.

 Inner 

flange

Follow instructions for depressed center wheel but also 

use back up pad over wheel.

Installing or removing abrasive disc

Optional accessory

NOTE:

 Use sander accessories specified in this man

-

ual. These must be purchased separately.

For 100 mm (4″) model

1

2

3

4

Fig.13

►    

1.

 Sanding lock nut 

2.

 Abrasive disc 

3.

 Rubber pad 

4.

 Inner flange

1.

  Mount the inner flange onto the spindle.

2.

  Mount the rubber pad onto the spindle.

3.

  Fit the disc on the rubber pad and screw the sand

-

ing lock nut onto the spindle.

4.

  Hold the spindle with the shaft lock, and securely 

tighten the sanding lock nut clockwise with the lock nut 

wrench.
To remove the disc, follow the installation procedure in 

reverse.

Summary of Contents for GA048G

























Reviews: