Makita G12010R Instructions For Use Manual Download Page 25 | Manualshive

Page: 25 / 44

background image

−

14

−

up to 30A

up to 30A

up to 20A

NEMA

5-20R

NEMA

L5-30R

NEMA

L14-30R

NEMA

5-20P

NEMA

L5-30P

NEMA

L14-30P

GFCI (Ground Fault
Circuit Interrupter)
Receptacle, duplex

(REC1)

Locking Receptacle
(REC2)

Locking Receptacle
(REC3)

Style

Ampere

Receptacle

AC plug

Description

up to 50A

Locking Receptacle
(REC4)

TABLE 1

■

Check the amperage of the receptacles used referring to

TABLE 1

, and be

sure not to take a current exceeding the specified amperage.

■

Be sure that the total wattage of all appliances dose not exceed the rated
output of the generator.

■

To take power out from the TWIST
LOCK RECEPTACLE, insert the
plug into the receptacle, and turn
it clockwise to the lock position.

■

Be sure to ground the generator if
the connected electrical device Is
grounded.

WARNING

TWIST

NOTE :

When the no-fuse breaker turns off during operation, the generator is over loaded
or the appliance is defective. Stop the generator immediately, check the appliance
and / or generator for overloading or detect and have repaired as necessary by
Makita dealer or service shop.

G12010R排対̲GU2000 05.1.20 1:38 PM ページ14

«
...
23
24
25
26
27
...
»

Summary of Contents for G12010R













































Reviews:

No comments

Related manuals for G12010R

Brand: XINDAK Pages: 9

Atlona Omega AT-OME-SR21

Brand: Panduit Pages: 28

Brand: NF Pages: 96

Brand: Northern Lights Pages: 35

Brand: JTS Pages: 8

Brand: Harman Kardon Pages: 16

Brand: Encore Pages: 27

Brand: Fronius Pages: 190

Brand: VigilLink Pages: 14

Brand: Fronius Pages: 92

Brand: Fitel Pages: 5

Brand: ZUCCHETTI Pages: 61

HDMI Encoder 8x

Brand: NetUP Pages: 44

Brand: Omron Pages: 400

Brand: M-system Pages: 2

Brand: Planet Pages: 17

Evershine TLC5000

Brand: Zeversolar Pages: 2

Brand: Wen Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands