Makita G12010R Instructions For Use Manual Download Page 41

Page: 41 / 44

10. PREPARATION FOR STORAGE

−

The following procedures should be followed prior to storage of your generator for
a period of 6 months or longer.

■

Drain fuel from fuel tank and strainer
(cup) carefully by disconnecting the
fuel line. Gasoline left in the fuel tank
will eventually deteriorate making
engine-starting difficult.

■

In order to remove the fuel in the
carburetor, run the engine at no-load
until it stops.

■

Disconnect the terminal of the battery.

■

Change engine oil.

■

Check for loose bolts and screws, tighten them if necessary.

■

Clean generator thoroughly with oiled cloth. Spray with preservative if
available. NEVER USE WATER TO CLEAN GENERATOR !

■

Store generator in a well ventilated, low humidity area.

SCREW for DRAIN

G12010R排対̲GU2000 05.1.20 1:38 PM ページ30

Summary of Contents for G12010R













































Search results

Summary of Contents for G12010R

Reviews:

Related manuals for G12010R

Brands by name

Popular brands

Makita G12010R, Instructions For Use Manual

Search results

Summary of Contents for G12010R

Reviews:

Related manuals for G12010R

Brands by name

Popular brands