86
2-2.
„Speed“ (Drehzahl)
Stellen Sie die Drehzahl ein.
2-3.
„Ignored Torque Time“ (Drehmoment ignorieren)
Wenn „Torque“ (Drehmoment) für „Pass Criteria for Phase“ (Zielkriterium für Stufe) / „Failure Criteria for
Phase“ (Kriterium für Fehlerbewertung) eingestellt ist, können Sie die Dauer einstellen, während der
Zustand nach dem Beginn dieser Phase nicht bewertet wird.
2-4.
„Slowstart“ (Langsamer Start)
Sie können die Dauer zum Erreichen der für „Speed“ (Drehzahl) eingestellten Drehzahl nach Beginn
dieser Phase einstellen.
3.
„Pass Criteria for Phase“ (Zielkriterium für Stufe)
3-1.
„Condition“ (Zustand)
Einstellen des Zustands, zu dem diese Phase betrieben wird.
・
„Clutch“ (Kupplung)
Erkennen der Kupplungsbetätigung und Festlegen des Ziels.
・
„Angle“ (Winkel)
Erkennen, dass das Produkt zum eingestellten Winkel gedreht wurde, und Festlegen des Ziels.
・
„Time“ (Zeit)
Erkennen, dass die eingestellte Zeit verstrichen ist, und Festlegen des Ziels.
・
„> Torque“ (>Drehmoment)
Erkennen, dass das Produkt den eingestellten Drehmoment (die Last) während seines Betriebs
überschritten hat, und Festlegen des Ziels.
・
„<Torque“ (<Drehmoment)
Erkennen, dass das Produkt unter den eingestellten Drehmoment (die Last) gefallen ist, und
Festlegen des Ziels.
3-2.
„OK Judgement“ (Ok Bewertung)
Stellen Sie die verwendeten Phasen zum Bestimmen, dass die Befestigungsarbeiten abgeschlossen
(abgesegnet) wurden, ein.
Sie können jeweils nur eine Phase für Vorwärtsdrehung / Rückwärtsdrehung einstellen.
4.
„Failure Criteria for Phase“ (Kriterium für Fehlerbewertung)
Die Einstellungen können durch Markieren des Kontrollkästchens ausgeführt werden.
Sie können den Zustand einstellen, auf dessen Grundlage während des Betriebs dieser Phase eine
anormale Befestigung (Phasenfehler) festgestellt wird.
4-1.
„Clutch“ (Kupplung)
Eine Störung wird festgestellt, wenn die Kupplung vor dem Bestimmen des Ziels erkannt wird.
4-2.
„> Angle“ (>Winkel)
Eine Störung wird festgestellt, wenn das Produkt vor dem Bestimmen des Ziels zum eingestellten
Winkel gedreht wird.
4-3.
„<Angle“ (<Winkel)
Eine Störung wird festgestellt, wenn das Produkt nach dem Bestimmen des Ziels nicht zum eingestellten
Winkel gedreht wird.
4-4.
„>Time“ (>Zeit)
Eine Störung wird festgestellt, wenn die eingestellte Zeit vor dem Bestimmen des Ziels verstrichen ist.
4-5.
„<Time“ (<Zeit)
Eine Störung wird festgestellt, wenn die eingestellte Zeit nach dem Bestimmen des Ziels nicht
verstrichen ist.
Summary of Contents for FL Series
