background image

NOTE:

 Depending on the conditions of use and the 

ambient temperature, the indication may differ slightly 

from the actual capacity.

Switch action

1

►  

1.

 Switch trigger

CAUTION:

 

Before installing the battery car-

tridge into the tool, always check to see that the 

switch trigger actuates properly and returns to 

the "OFF" position when released.

To start the tool, simply pull the switch trigger. Tool 

speed is increased by increasing pressure on the switch 

trigger. Release the switch trigger to stop.

Electric brake

This tool is equipped with an electric brake. If the tool 

consistently fails to quickly stop after the switch trigger is 

released, have the tool serviced at a Makita service center.

Lighting up the front lamp

1

►  

1.

 Lamp

CAUTION:

 

Do not look in the light or see the 

source of light directly.

Pull the switch trigger to light up the lamp. The lamp keeps on 

lighting while the switch trigger is being pulled. The lamp goes 

out approximately 10 seconds after releasing the switch trigger.

NOTE:

 Use a dry cloth to wipe the dirt off the lens of 

the lamp. Be careful not to scratch the lens of lamp, or 

it may lower the illumination.

Reversing switch action

1

A

B

►  

1.

 Reversing switch lever

CAUTION:

 

Always check the direction of 

rotation before operation.

CAUTION:

 

Use the reversing switch only after 

the tool comes to a complete stop.

 Changing the 

direction of rotation before the tool stops may dam

-

age the tool.

CAUTION:

 

When not operating the tool, 

always set the reversing switch lever to the neu-

tral position.

This tool has a reversing switch to change the direction 

of rotation. Depress the reversing switch lever from the 

A side for clockwise rotation or from the B side for coun

-

terclockwise rotation.

When the reversing switch lever is in the neutral posi-

tion, the switch trigger cannot be pulled.

Speed change

1

►  

1.

 Speed change lever

CAUTION:

 

Always set the speed change lever 

fully to the correct position.

 If you operate the 

tool with the speed change lever positioned halfway 

between the "1" side and "2" side, the tool may be 

damaged.

CAUTION:

 

Do not use the speed change lever 

while the tool is running.

 The tool may be damaged.

Summary of Contents for FD09












Reviews: