background image

Using the tool as a hand screwdriver

Switch off the tool.  

Move the reversing switch lever to the neutral position. 

Turn the adjusting ring so that the arrow points to 

the 

 marking. 

Turn the tool.

NOTE:

 This use is convenient for checking the 

screwdriving.

NOTE:

 Do not use the tool for work requiring exces-

sive force, such as tightening bolt or removing rusted 

screws.

Using holster

Optional accessory

CAUTION:

 

When using the holster, remove a 

driver bit/drill bit from the tool.

CAUTION:

 

Turn off the tool and wait until it 

comes to a complete stop before placing it in the 

holster.  

Be sure to close the holster securely with the 

holster button so that it holds the tool firmly.

1.

Thread a waist belt or similar through holster holder.

1

2

►  

1.

 Holster holder 

2.

 Waist belt

2.

Put the tool in the holster and lock it with the hol-

ster button.

You can keep two driver bits at the front of the holster.

MAINTENANCE

CAUTION:

 

Always be sure that the tool is 

switched off and the battery cartridge is removed before 

attempting to perform inspection or maintenance.

NOTICE:

 

Never use gasoline, benzine, thinner, 

alcohol or the like. Discoloration, deformation or 

cracks may result.

To maintain product SAFETY and RELIABILITY, 

repairs, any other maintenance or adjustment should 

be performed by Makita Authorized or Factory Service 

Centers, always using Makita replacement parts.

Summary of Contents for FD09












Reviews: