Makita DUR191U Instruction Manual Download Page 21

Page: 21 / 24

ENGLISH

Replacing the plastic blade

Replace the plastic blade if it is worn out or broken.

When installing the plastic blade, align the direction of
the arrow on the blade with that of the protector.

►

Arrow on the protector

Arrow on the blade

TROUBLESHOOTING

Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual,

do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace-
ment parts for repairs.

State of abnormality

Probable cause (malfunction)

Remedy

Motor does not run.

Battery cartridge is not installed.

Install the battery cartridge.

Battery problem (under voltage)

Recharge the battery. If recharging is not effective,

replace battery.

The drive system does not work
correctly.

Ask your local authorized service center for repair.

Motor stops running after a little use.

Battery's charge level is low.

Recharge the battery. If recharging is not effective,

replace battery.

Overheating.

Stop using of tool to allow it to cool down.

It does not reach maximum RPM.

Battery is installed improperly.

Install the battery cartridge as described in this
manual.

Battery power is dropping.

Recharge the battery. If recharging is not effective,

replace battery.

The drive system does not work
correctly.

Ask your local authorized service center for repair.

Cutting tool does not rotate:

stop the machine immediately!

Foreign object such as a branch is

jammed between the guard and the

cutting tool.

Remove the foreign object.

The drive system does not work
correctly.

Ask your local authorized service center for repair.

Abnormal vibration:

stop the machine immediately!

One end of the nylon cord has been
broken.

Tap the nylon cutting head against the ground while
it is rotating to cause the cord to feed.

The drive system does not work
correctly.

Ask your local authorized service center for repair.

Cutting tool and motor cannot stop:

Remove the battery immediately!

Electric or electronic malfunction.

Remove the battery and ask your local authorized
service center for repair.

Summary of Contents for DUR191U

























Search results

Summary of Contents for DUR191U

Reviews:

Related manuals for DUR191U

Brands by name

Popular brands

Makita DUR191U, Instruction Manual

Search results

Summary of Contents for DUR191U

Reviews:

Related manuals for DUR191U

Brands by name

Popular brands