18 ENGLISH
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
CAUTION:
When inspecting or maintaining
the tool, always put the tool down.
Assembling or
adjusting the tool in an upright position may result in
serious injury.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Cleaning the tool
Clean the tool by wiping off dust with a dry cloth or one
dipped in soapy water and wrung out.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
Shear blade maintenance
Before the operation or once per hour during operation,
apply low-viscosity oil (machine oil, or spray-type lubri
-
cating oil) to the shear blades.
►
Fig.41
After operation, remove dust from both sides of the
shear blades with a wired brush, wipe it off with a cloth
and then apply low-viscosity oil (machine oil, or spray-
type lubricating oil) to the shear blades.
►
Fig.42
NOTICE:
Do not wash the shear blades in water.
Doing so may cause rust or damage to the tool.
NOTICE:
Dirt and corrosion cause excessive
blade friction and shorten the operating time per
battery charge.
Storage
Attach the blade cover to the shear blades so that the
blades are not exposed. Store the tool out of the reach
of children. Store the tool in a place not exposed to
moisture or rain.
Grinding the shear blades
NOTICE:
If the shear blades have considerably
deformed by grinding, replace the shear blades
with new ones.
1.
Install the battery cartridge to the tool.
2.
Turn on and start the tool so that the upper blade
and lower blade are positioned alternately.
►
Fig.43
3.
Turn off the tool and remove the battery cartridge
from the tool.
4.
Remove the screw, and then remove the branch
catcher.
►
Fig.44:
1.
Screw
2.
Branch catcher
5.
Set the angle of a file to 45°, and grind the upper
blade from 3 directions with the file.
►
Fig.45:
(1)
File
(2)
45°
CAUTION:
Before grinding the shear blades,
make sure that the tool is switched off and the
battery cartridge is removed from the tool.
6.
Place the tool upside down, and then remove the
burrs from the shear blades with the dressing stone.
►
Fig.46:
1.
Dressing stone
7.
Set the angle of the file to 45°, and grind the lower
blade from 3 directions with the file.
8.
Return the tool to normal position, and then
remove the burrs from the shear blades with the dress-
ing stone.
9.
Attach the branch catcher by tightening the screw.
Grease lubrication
Interval of lubrication:
Every 25 operating hours
1.
Remove the bolt from the hole for lubrication.
►
Fig.47:
1.
Bolt
2.
Remove the cap from the grease vessel. Align the
outlet of the grease vessel with the hole on the cover,
and then press the outlet of the grease vessel onto the
hole.
►
Fig.48:
1.
Grease vessel
2.
Hole
3.
Apply the grease to the tool (Approximately 5 g as
a guide).
4.
Tighten the bolt.
Summary of Contents for DUN600L
