19 ENGLISH
NOTE:
Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
Tool / battery protection system
The
tool
is
equipped with
a
tool/battery protection system.
This
system
automatically
cuts
off
power
to
the
motor
to
extend
tool
and
battery
life.
The
tool
will
automatically stop during operation if the
tool or battery is placed under one of the following
conditions:
Overload protection
When the battery is operated in a manner that causes it
to draw an abnormally high current, the tool
automatically stops and the main power lamp blinks in
green. In this situation, turn the tool off and stop the
application that
caused
the
tool
to
become
overloaded.
Then
turn
the tool on to restart.
Overheat protection
When the tool or battery is overheated, the tool stops
automatically and the main power lamp lights up in red.
In this case, let the tool and battery cool before turning
the tool on again.
NOTE:
In high temperature environment, the overheat
protection likely to work and the tool stops
automatically.
Overdischarge protection
When the battery capacity is not enough, the tool stops
automatically and the main power lamp blinks in red. In
this case, remove the battery from the tool and charge
the battery.
Main power switch
WARNING:
Always turn off the main power
switch when not in use.
To
turn
on
the
tool,
press
the
main
power
switch
until
the
main
power
lamp
lights
up
in
green.
To
turn
off,
press the main power switch
again. ►
Fig.5:
1.
Main power lamp
2.
Main
power switch
NOTE:
The
main
power
lamp
blinks
in
green
if
the
switch trigger is pulled under
unoperatable conditions. The
lamp
blinks
in
one
of
the
following conditions.
•
When
you
turn
on
the
main
power
switch
while
holding down the lock-off lever
and the switch trigger.
•
When
you
pull
the
switch
trigger
while
the
chain
brake is applied.
•
When
you
release
the
chain
brake
while
holding
down the lock-off lever and pulling the
switch trigger.
NOTE:
This
chain
saw
employs
the
auto
power-off function.
To
avoid
unintentional
start
up,
the
main
power switch will automatically shut down
when the switch trigger is not pulled for a certain
period after the main power switch is turned on.
You
can
use
the
tool
in
the
Torque
Boost
mode
for
cutting
thick
branches or
hard
branches.
To
use
the
tool
in
the
Torque
Boost
mode,
when
the
tool
is
turned
off,
press the
main power switch for a few seconds until the main
power lamp lights up in yellow.
NOTE:
You
can
use
the
tool
in
the
Torque
Boost
mode up to 30 seconds.
Depending on the usage conditions, this mode shifts
to the normal mode in less than 30 seconds.
NOTE:
If the main power lamp blinks in yellow when
you press the main power switch for a few seconds,
the
Torque
Boost
mode
is
Indicator lamps
Remaining
capacity
Lighted
Off
Blinking
% to 100%
75
% to 75%
50
25
% to 50%
% to 25%
0
Charge the
battery.
The
ba
may have
malfunctioned.
Summary of Contents for DUC204
