21 ENGLISH
3.
Align the pipe of the tool with the groove inside the
wire guide B, and assemble them.
►
Fig.43:
1.
Pipe
2.
Groove
3.
Wire guide B
4.
Fix wire guide B by temporarily tightening bolt A.
►
Fig.44:
1.
Bolt A
2.
Wire guide B
5.
Install the contact plate cover in the direction of the
arrow.
►
Fig.45:
1.
Contact plate cover
6.
Fix wire guide B and contact plate cover securely
by tightening bolt A and bolt B.
►
Fig.46:
1.
Wire guide B
2.
Contact plate
cover
3.
Bolt A
4.
Bolt B
7.
After assembling,
confirm
that
the
contact
plate
can
move
as
shown
in
the
figure. ►
Fig.47:
1.
Contact
plate
NOTE:
If the contact plate is caught, press it as shown
in
the
figure.
►
Fig.48
Error display and error tone
CAUTION:
During inspection, be sure to lock the trigger, turn the power off, and remove the battery
cartridge.
Failure to do so may cause an accident.
CAUTION:
When you turn the power on, never bring your limbs or face close to the binding or rotating
parts of the tool tip.
Otherwise, you
may
be
injured.
CAUTION:
When the power is turned on, never touch the binding or rotating parts of the tool tip.
Otherwise, you
may
be
injured.
CAUTION:
If an error tone sounds, or if the tool malfunctions, immediately stop using the tool.
Error tone and display
If an error occurs, an error tone will sound, and an error number will be shown on the display panel. Refer to the
following table and take appropriate actions. If the error persists, ask Makita Authorized Service Centers for repairs.
Display
Symptom
Possible cause
Solution
1
The tool stops operating.
The wire has been used up.
Load new tie wire.
Tie wire is not loaded.
Load tie wire.
Wire feeding has failed.
Check the orientation of the tie
wire.
Unload the tie wire, and load it
again.
Clean the path of wire.
2
The tool stops operating.
The curl guide is open.
Close the curl guide.
3
The tool does not perform the
tying process in continuous
actuation mode.
The contact plate is caught.
Release the contact plate from
being caught.
4
The tool does not start.
The tool stops operating.
The battery has been
discharged.
The temperature of the battery
cartridge is abnormally high.
Recharge the battery.
Cool the battery cartridge
down.
Replace the battery cartridge
with a recharged one.
5
The tool stops operating.
The motor is overloaded.
Determine the cause of the
obstruction of the motor rotation
and solve the problem.
Motor failure
6
The tool stops operating.
The temperature of the tool is
abnormally high.
Cool the tool down.
7
The tool does not start.
The tool stops operating.
Tool failure
Ask Makita Authorized Service
Centers for repairs.
Summary of Contents for DTR180
