background image

8 ENGLISH

Impact force grade displayed 

on panel

Maximum blows

Purpose

Example of application

Hard

T

S

H

3,800 min

-1

 (/min)

Tightening when force and 

speed are desired.

Tightening underwork mate-

rials, tightening long screws, 

tightening bolts.

Medium

T

S

H

2,600 min

-1

 (/min)

Tightening when a good finish

-

ing is needed.

Tightening finishing boards, 

plaster boards.

Soft

T

S

H

1,100 min

-1

 (/min)

Tightening with less force to 

avoid screw thread breakage.

Tightening sash screws, tight-

ening small screws such as M6.

T mode

T

S

H

2,600 min

-1

 (/min)

Tightening when speed and 

good finishing are needed.

Tightening self drilling screws.

NOTE:

 When all lamps on the switch panel go out, the tool is turned off to save the battery power. The impact force 

grade can be checked by pulling the switch trigger to the extent that the tool does not operate.

NOTE:

 While pulling the switch trigger, the impact force grade cannot be changed.

ASSEMBLY

CAUTION:

 

Always be sure that the tool is 

switched off and the battery cartridge is removed 

before carrying out any work on the tool.

Installing or removing driver bit/

socket bit

Use only driver bit/socket bit that has inserting portion 

shown in the figure. Do not use any other driver bit/

socket bit.

For tool with shallow driver bit hole

A=12mm

 

B=9mm

 

Use only these type of driver 

bit. Follow the procedure 

1. (Note) Bit-piece is not 

necessary.

For tool with deep driver bit hole

A=17mm

 

B=14mm

To install these types of driver 

bits, follow the procedure 1.

A=12mm

 

B=9mm

To install these types of driver 

bits, follow the procedure 2. 

(Note) Bit-piece is necessary 

for installing the bit.

Procedure 1

For tool without one-touch type sleeve

1

2

►    

1.

 Driver bit 

2.

 Sleeve

To install the driver bit, pull the sleeve in the direction of 

the arrow and insert the driver bit into the sleeve as far 

as it will go. 

Then release the sleeve to secure the driver bit.

For tool with one-touch type sleeve

To install the driver bit, insert the driver bit into the 

sleeve as far as it will go.

Summary of Contents for DLX2176TJ

























Reviews: