background image

7 ENGLISH

Overheat protection

This protection works when the tool or battery is over-

heated. In this situation, let the tool and battery cool 

before turning the tool on again.

Overdischarge protection

This protection works when the remaining battery 

capacity gets low. In this situation, remove the battery 

from the tool and charge the battery.

Switch action

CAUTION:

 

Before installing the battery car-

tridge into the tool, always check to see that the 

switch trigger actuates properly and returns to 

the "OFF" position when released.

1

►    

1.

 Switch trigger

To start the tool, simply pull the switch trigger. Tool 

speed is increased by increasing pressure on the switch 

trigger. Release the switch trigger to stop.

NOTE:

 The tool automatically stops if you keep pull-

ing the switch trigger for about 6 minutes.

Lighting up the front lamp

CAUTION:

 

Do not look in the light or see the 

source of light directly.

1

►    

1.

 Lamp

Pull the switch trigger to light up the lamp. The lamp 

keeps on lighting while the switch trigger is being pulled. 

The lamp goes out approximately 10 seconds after 

releasing the switch trigger.

NOTE:

 When the tool is overheated, the tool stops 

automatically and the lamp starts flashing. In this 

case, release the switch trigger. The lamp turns off in 

one minute.

NOTE:

 Use a dry cloth to wipe the dirt off the lens of 

the lamp. Be careful not to scratch the lens of lamp, or 

it may lower the illumination.

Reversing switch action

CAUTION:

 

Always check the direction of 

rotation before operation.

CAUTION:

 

Use the reversing switch only after 

the tool comes to a complete stop.

 Changing the 

direction of rotation before the tool stops may dam-

age the tool.

CAUTION:

 

When not operating the tool, 

always set the reversing switch lever to the neu-

tral position.

1

A

B

►    

1.

 Reversing switch lever

This tool has a reversing switch to change the direction 

of rotation. Depress the reversing switch lever from the 

A side for clockwise rotation or from the B side for coun-

terclockwise rotation.

When the reversing switch lever is in the neutral posi-

tion, the switch trigger cannot be pulled.

Summary of Contents for DHP486RTE













Reviews: