background image

11 ENGLISH

Hammer drilling operation

CAUTION:

 

There is a tremendous and sudden 

twisting force exerted on the tool/drill bit at the 

time of hole breakthrough, when the hole becomes 

clogged with chips and particles, or when striking 

reinforcing rods embedded in the concrete.

First, turn the adjusting ring so that the arrow on the tool 

body points to the 

 marking.

Be sure to use a tungsten-carbide tipped drill bit.

Position the drill bit at the desired location for the hole, 

then pull the switch trigger. Do not force the tool. Light 

pressure gives best results. Keep the tool in position 

and prevent it from slipping away from the hole.

Do not apply more pressure when the hole becomes 

clogged with chips or particles. Instead, run the tool at 

an idle, then remove the drill bit partially from the hole. 

By repeating this several times, the hole will be cleaned 

out and normal drilling may be resumed.

Blow-out bulb

Optional accessory

1

►    

1.

 Blow-out bulb

After drilling the hole, use the blow-out bulb to clean the 

dust out of the hole.

Drilling operation

CAUTION:

 

Pressing excessively on the tool will 

not speed up the drilling.

 In fact, this excessive pressure 

will only serve to damage the tip of your drill bit, decrease 

the tool performance and shorten the service life of the tool.

CAUTION:

 

Hold the tool firmly and exert care 

when the drill bit begins to break through the 

workpiece.

 There is a tremendous force exerted on 

the tool/drill bit at the time of hole break through.

CAUTION:

 

A stuck drill bit can be removed 

simply by setting the reversing switch to reverse 

rotation in order to back out. However, the tool 

may back out abruptly if you do not hold it firmly.

CAUTION:

 

Always secure workpieces in a 

vise or similar hold-down device.

CAUTION:

 

If the tool is operated continuously 

until the battery cartridge has discharged, allow 

the tool to rest for 15 minutes before proceeding 

with a fresh battery.

First, turn the adjusting ring so that the arrow points to 

the 

 marking. Then proceed as follows.

Drilling in wood

When drilling in wood, the best results are obtained with 

wood drills equipped with a guide screw. The guide screw 

makes drilling easier by pulling the drill bit into the workpiece.

Drilling in metal

To prevent the drill bit from slipping when starting a 

hole, make an indentation with a center-punch and 

hammer at the point to be drilled. Place the point of the 

drill bit in the indentation and start drilling.

Use a cutting lubricant when drilling metals. The excep-

tions are iron and brass which should be drilled dry.

MAINTENANCE

CAUTION:

 

Always be sure that the tool is 

switched off and the battery cartridge is removed 

before attempting to perform inspection or 

maintenance.

NOTICE:

 

Never use gasoline, benzine, thinner, 

alcohol or the like. Discoloration, deformation or 

cracks may result.

To maintain product SAFETY and RELIABILITY, 

repairs, any other maintenance or adjustment should 

be performed by Makita Authorized or Factory Service 

Centers, always using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

 

These accessories or attachments 

are recommended for use with your Makita tool 

specified in this manual.

 The use of any other 

accessories or attachments might present a risk of 

injury to persons. Only use accessory or attachment 

for its stated purpose.

If you need any assistance for more details regard-

ing these accessories, ask your local Makita Service 

Center.
• 

Drill bits

• 

Driver bits

• 

Tungsten-carbide tipped drill bit

• 

Blow-out bulb

• Hook
• 

Grip assembly

• 

Depth rod

• 

Rubber pad assembly

• 

Wool bonnet

• 

Foam polishing pad

• 

Makita genuine battery and charger

NOTE:

 Some items in the list may be included in the 

tool package as standard accessories. They may 

differ from country to country.

Summary of Contents for DHP486RTE













Reviews: