background image

9 ENGLISH

NOTE:

 Both shallower type (A=12 mm, B=9 mm) and 

deeper type (A=17 mm, B=14 mm) of driver bits can 

be used.

To install the driver bit, pull the sleeve in the direction of 

the arrow and insert the driver bit into the sleeve as far 

as it will go. 

Then release the sleeve to secure the driver bit.

2

1

►    

1.

 Driver bit 

2.

 Sleeve

To remove the driver bit, pull the sleeve in the direction 

of the arrow and pull the driver bit out.

NOTE:

 If the driver bit is not inserted deep enough 

into the sleeve, the sleeve will not return to its original 

position and the driver bit will not be secured. In this 

case, try re-inserting the bit according to the instruc

-

tions above.

NOTE:

 After inserting the driver bit, make sure that it 

is firmly secured. If it comes out, do not use it.

Installing hook

CAUTION:

 

When installing the hook, always 

secure it with the screw firmly.

 If not, the hook 

may come off from the tool and result in the personal 

injury.

1

2 3

►    

1.

 Groove 

2.

 Hook 

3.

 Screw

The hook is convenient for temporarily hanging the tool. 

This can be installed on either side of the tool. To install 

the hook, insert it into a groove in the tool housing on 

either side and then secure it with a screw. To remove, 

loosen the screw and then take it out.

Installing driver bit holder

Optional accessory

1

2

►    

1.

 Driver bit holder 

2.

 Driver bit

Fit the driver bit holder into the protrusion at the tool foot 

on either right or left side and secure it with a screw.

When not using the driver bit, keep it in the driver bit 

holders. Driver bits 45 mm-long can be kept there.

OPERATION

CAUTION:

 

Always insert the battery cartridge 

all the way until it locks in place.

 If you can see the 

red indicator on the upper side of the button, it is not 

locked completely. Insert it fully until the red indicator 

cannot be seen. If not, it may accidentally fall out of 

the tool, causing injury to you or someone around 

you.

CAUTION:

 

When the speed comes down 

extremely, reduce the load or stop the tool to 

avoid the tool damage.

Hold the tool firmly with one hand on the grip and the 

other hand on the bottom of the battery cartridge to 

control the twisting action.

Summary of Contents for DF333DWAE













Reviews: