30 ENGLISH
Refilling the tire with air
Check that the air in the tire for the front and rear
wheels is not missing. If the air in the tire is insufficient,
refill the tire with air using an inflator. The air pressure
is as follows:
•
Tire for front wheel: 280 kPa (40 PSI)
•
Tire for rear wheel: 525 kPa (75 PSI)
Front wheel
►
Fig.64
Rear wheel
►
Fig.65
Replacing the tire
CAUTION:
Before replacing the tires, be sure to unload all objects from the machine.
CAUTION:
When replacing the tires, wear the gloves.
Replacing the tire of front wheel
NOTE:
When installing the gray tire, install it so that the valve faces outward.
►
Fig.66
Replacing the tire of rear wheel
►
Fig.67
►
Fig.68
TROUBLESHOOTING
Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual,
do not disassemble the machine. Instead, ask Makita Authorized Service Centers, always using Makita replacement
parts for repairs.
State of abnormality
Main power lamp
Cause
Remedy
The machine does not
turn on.
Turned off.
Two battery cartridges are not
installed.
Install two charged battery cartridges.
Battery problem (under voltage) Recharge the battery cartridge. If recharging
is not effective, replace battery cartridge.
Battery selection switch is not
in the correct position.
Select the correct battery using the battery
selection switch.
The machine does not
start.
The lamp blinks in red.
Battery's charge level is low.
Recharge the battery cartridge. If recharging
is not effective, replace battery cartridge.
At least one of the battery is
empty.
Remove the empty battery, or replace it with
charged one. In this case, the far left lamp
of the battery indicator of the corresponding
battery blinks.
The lamp blinks in
green.
The lock key is not inserted.
Insert the lock key and turn it clockwise.
The machine stopped due to
overload.
Reduce the loaded objects.
The front or rear wheels are
stuck or locked.
Remove the cause of stuck or locked wheels.
The lamp lights up
in red.
The machine stopped due to
overheat.
Cool down the machine and battery.
The lamp blinks in red
and green alternately.
The lock key is not inserted.
Insert the lock key and turn it clockwise.
The machine detected an
abnormality.
Turn off the machine, and then back on.
A malfunction of machine has occurred. Ask
Makita Authorized Service Centers for repair.
The lamp lights up in
green.
The neutral change lever is not
in its original position.
Lock the brake lever, and then return the
neutral change lever to its original position.
The machine stops
after a little use.
The lamp blinks in red.
Battery's charge level is low.
Recharge the battery cartridge. If recharging
is not effective, replace battery cartridge.
Summary of Contents for DCU603
