![background image](http://html.mh-extra.com/html/makita/dcs550/dcs550_instruction-manual_224466005.webp)
5
Lower guard function
16.
Check lower guard for proper closing before
each use. Do not operate the tool if lower
guard does not move freely and close
instantly. Never clamp or tie the lower guard
into the open position.
If tool is accidentally
dropped, lower guard may be bent. Raise the
lower guard with the retracting lever and make
sure it moves freely and does not touch the blade
or any other part, in all angles and depths of cut.
17.
Check the operation and condition of the lower
guard spring. If the guard and the spring are not
operating properly, they must be serviced before
use.
Lower guard may operate sluggishly due to
damaged parts, gummy deposits, or a buildup of debris.
18.
Lower guard may be retracted manually only for
special cuts such as "plunge cuts" and "compound
cuts". Raise lower guard by retracting handle and
as soon as blade enters the material, the lower
guard must be released.
For all other sawing, the
lower guard should operate automatically.
19.
Always observe that the lower guard is
covering the blade before placing tool down on
bench or floor.
An unprotected, coasting blade will
cause the tool to walk backwards, cutting whatever
is in its path. Be aware of the time it takes for the
blade to stop after switch is released.
20.
To check lower guard, open lower guard by hand,
then release and watch guard closure. Also check
to see that retracting handle does not touch tool
housing.
Leaving blade exposed is VERY
DANGEROUS and can lead to serious personal injury.
Additional safety warnings
21.
Do not stop the blades by lateral pressure on
the blade.
22.
DANGER:
Do not attempt to remove cut material when
blade is moving.
CAUTION: Blades coast after turn off.
23.
Place the wider portion of the tool base on that part
of the workpiece which is solidly supported, not on
the section that will fall off when the cut is made.
24.
Never attempt to make a cut with the tool held
upside down in a vise. This is extremely
dangerous and can lead to serious accidents.
25.
Wear safety goggles and hearing protection
during operation.
26.
Always use blades recommended in this
manual. Do not use any abrasive wheels.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to safety
rules for the subject product. MISUSE or failure to
follow the safety rules stated in this instruction manual
may cause serious personal injury.
ENC007-8
IMPORTANT SAFETY
INSTRUCTIONS
FOR BATTERY CARTRIDGE
1.
Before using battery cartridge, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product
using battery.
2.
Do not disassemble battery cartridge.
3.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4.
If electrolyte gets into your eyes, rinse them
out with clear water and seek medical
attention right away. It may result in loss of
your eyesight.
5.
Do not short the battery cartridge:
(1)
Do not touch the terminals with any
conductive material.
(2)
Avoid storing battery cartridge in a
container with other metal objects such
as nails, coins, etc.
(3)
Do not expose battery cartridge to water
or rain.
A battery short can cause a large current flow,
overheating, possible burns and even a
breakdown.
6.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50
゚
C (122
゚
F).
7.
Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
8.
Be careful not to drop or strike battery.
9.
Do not use a damaged battery.
10.
Follow your local regulations relating to
disposal of battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1.
Charge the battery cartridge before
completely discharged.
Always stop tool operation and charge the
battery cartridge when you notice less tool power.
2.
Never recharge a fully charged battery
cartridge.
Overcharging shortens the battery service life.
3.
Charge the battery cartridge with room
temperature at 10
゚
C - 40
゚
C (50
゚
F - 104
゚
F).
Let a hot battery cartridge cool down before
charging it.
4.
Charge the battery cartridge once in every six
months if you do not use it for a long period
of time.
Summary of Contents for DCS550
Page 70: ...70 ...
Page 71: ...71 ...
Page 72: ...72 Makita Corporation Anjo Aichi Japan www makita com 885282 964 ...